2Specifications | HP m300 specs

The Expansion Base is designed in accordance with ANSI specifications (no. X3.131-1993, Rev 10h) and IEEE 802.3 specifications.

NOTE: This product is designed for IT power systems with phase-to-phase voltage not exceeding 240Vrms minimum charge.

6-2Specifications

Image 63

HP m300 manual 2Specifications

Contents

Compaq ArmadaStation EM Maintenance and Service Guide Contents Appendix Using this Guide SymbolsTechnician Notes Locating Additional Information Serial Number Product Description ArmadaStation EM Features External Connectors Security Features ArmadaStation EM Components ArmadaStation EM Front ComponentsDescription Function ArmadaStation EM Right Side Components Volume control switch ArmadaStation EM Rear Panel Components ArmadaStation EM Rear Panel Components Device Activity LightsMultiBays MultiBay/Device Compatibility Half-Height Bay Security LockPCI Expansion Boards Before Replacing Parts Troubleshooting Problem Probable Cause Recommended Actions Problems and SolutionsSolving Docking and Undocking Problems Solving Expansion Board Problems Solving External Keyboard Problems Solving External Mouse ProblemsSolving Expansion Device Installation Problems Press any key or click the mouse Solving External Monitor Problems Serial Number Location Illustrated Parts Catalog Compaq ArmadaStation EM Components Compaq ArmadaStation EM Components Description Spare Parts Compaq ArmadaStation EM Components Plastics Kit Components Plastics Kit Components Spare Part NumberItem Description MultiBay Option Cable Kit Components Spare Part Number MultiBay Option Cable Kit Miscellaneous Spare Parts Miscellaneous not illustratedSpare Part Number Electrostatic Discharge Removal and Replacement Preliminaries Relative Humidity Event 10% 40% 55% Generating StaticPreventing Electrostatic Damage to Equipment Typical Electrostatic Voltages Method Preventing Damage to DrivesGrounding Methods Static Shielding Protection Levels Grounding Equipment Grounding Workstations Recommended Materials and Equipment Service Considerations Tool and Software RequirementsScrews Plastic Parts Cables and Connectors Removal and Replacement Procedures Expansion Base Disassembly Sequence Disassembly Sequence Chart Disconnecting the Expansion Base Preparing the Expansion Base for Disassembly Expansion Base Feet External Components Removing the Tray Tray Removing the Connector Cover Connector Cover Removing the Rear Bezel Rear Bezel Sliding the Manual Release Lever Locating the Expansion Slots PCI Expansion Boards 10.Removing the Expansion Slot Cover 11.Installing an Expansion Board 12.Removing the Top Cover Screws Top Cover Swing the top cover up and forward to remove it Figure Half-Height Bay Installing a Half-Height Drive 15.Removing the Half-Height Bay Blank Bezel Cover 16.Removing the Half-Height Drive Screws 17.Attaching the Bezel Cage to the Half-Height Drive 18.Connecting the Power Cable 19.Connecting the Diskette Drive Cable 20.Connecting the Hard Drive Cable 21.Connecting the CD-ROM Drive/Audio Cable 22.Installing a Half-Height Drive 23.Removing the Left Speaker Left Speaker MultiBay 24.Disconnecting the Half-Height Bay and Left Speaker Cables 25.Removing the MultiBay and Control Panel 26.Removing the Control Panel Control Panel Mechanism Assembly 28.Removing the Mechanism Assembly Power Supply 30.Removing the Power Supply 31.Removing the Backplane Backplane Expansion Base Physical and Environmental Specifications PecificationsMetric 2Specifications Connector PIN Assignments Table A-1 Headphone JackTable A-2 Microphone Jack Table A-5 Serial Connector Table A-3Table A-4 Table A-6 Table A-7 Stereo Line-out JackTable A-8 Stereo Line-in Jack Signal Pin Table A-13 Docking Connector PDATA6 LD14 Pin Signal Power Cord SET Requirements Conductor Power Cord SetGeneral Requirements Conductor Power Cord Set Requirements-By Country Country-Specific RequirementsCountry Accredited Agency Applicable Note Numbers Index PCI Index