Manuals / HP / Computer Equipment / Personal Computer

HP Vectra VL 5/xxx manual Jumper Settings, Configuring an IDE Device After Installation

Models: Vectra VL 5/xxx

1 110

Download 110 pages 28.95 Kb

Page 41

2 How to Install Accessories In Your PC

Installing Mass Storage Devices

Up to three IDE devices can be connected to the system board using these data cables.(Refer to the storage device’s manual to check whether you need to set jumpers, or if there are any special installation procedures.)

			Examples of multiple IDE drive combinations

		Configuration		Connections to data cables

	1	Hard disk drive	1.	Bootable hard disk drive:	First connector, Primary IDE Cable

	2	Hard disk drives	1.	Bootable hard disk drive:	First connector, Primary IDE Cable
			2.	Second hard disk drive:	Second connector, Primary IDE Cable

	3	Hard disk drives	1.	Bootable hard disk drive:	First connector, Primary IDE Cable
			2.	Second hard disk drive:	Second connector, Primary IDE Cable
			3.	Third hard disk drive:	Secondary IDE Cable

	1	Hard disk drive	1.	Bootable hard disk drive:	First connector, Primary IDE Cable
	1	CD-ROM	2.	CD-ROM:	Secondary IDE Cable

	2	Hard disk drives	1.	Bootable hard disk drive:	First connector, Primary IDE Cable
	1	CD-ROM	2.	Second hard disk drive:	Second connector, Primary IDE Cable
			3.	CD-ROM:	Secondary IDE Cable
Jumper Settings
Jumper Settings	Refer to the IDE drive’s manual to see if you must set jumpers. The drive
	jumper should be set to “cable select”.

Configuring an IDE Device After Installation

After installing a second IDE drive, or after installing any flexible disk drive, you will need to verify that your PC has correctly identified the new configuration, by viewing the HP Summary Screen. Refer to the page 66. If the configuration is not correct, run the Setup program to configure the device. Refer to “HP Setup Program” on page 66.

IDE drives are automatically detected by the Setup program. However, a newly installed CD-ROM may require that you install an appropriate device driver. Refer to your operating system documentation for details. For information on how to obtain the latest available drivers from HP, refer to page 73.

29

Image 41

HP Vectra VL 5/xxx Jumper Settings, Configuring an IDE Device After Installation, Configuration Connections to data cables

Contents

User’s Guide Page User’s Guide Who this Manual is For Important Safety InformationImportant Ergonomic Information Page Contents Removing and Replacing the Cover Installing Mass Storage DevicesInstalling Accessory Boards If Your PC Has a Software Problem Hewlett Packard Support and Information Services HP Setup ProgramGlossary Index Xii Setting Up and Using Your PC Accessories When you receive your PC, unpack all the componentsUnpacking Your PC Try to move it without helpConnections for Models with Integrated Video Display Connecting the Mouse, Keyboard, Display and PrinterConnections for Models with MGA Millennium Video Board Electronic servicesConnecting to a Network Connecting Audio Accessories Grounded outlet Connecting the Power CablesYour PC’s Hardware Control Panel Press this button to turn the power on or off to your PCYour PC’s hardware control panel is on the front of your PC Scsi hard disk drive, this light will not workStarting Your PC Starting and Stopping Your PCInitializing Your Software Starting the PC for the First TimeAfter Your PC Has Restarted Stopping Your PC Creating Master DiskettesSetting an Administrator Password Setting PasswordsPassword, on Setting a User PasswordThen press ActionAdditional Information and Help Using Power ManagementSetting Up and Using Your PC Additional Information and Help How to Install Accessories In Your PC Cache Memory Up to Four Accessory Boards Accessories You Can InstallFront-Access Device Shelf Video MemoryCheck that you have installed all your accessories Replacing the Cover after Installing AccessoriesRemoving and Replacing the Cover Removing the CoverMoving and Replacing the Power Supply Static electricity can damage electronic components Installing MemoryInstalling Main Memory Identified here as C is the one closest to the processor All cables and power cordsClip and pull the module forward and out of the socket Refer toHandle the accessory as little as possible and with care Installing an Optional Cache Memory ModuleUpgrade this to 512 KB Installing a Video Memory Upgrade Integrated Video Models To Install Video Memory ModulesAfter Installing a Video Memory Upgrade Upgrading the MGA Millennium Board Memory Switch Use Switch Block to Connecting IDE Devices Installing Mass Storage DevicesConfiguring an IDE Device After Installation Jumper SettingsConfiguration Connections to data cables Examples of multiple IDE drive combinationsInstalling an IDE Hard Disk Drive in the Rear Shelf Installing an IDE Hard Disk Drive in the Bottom Shelf Page Tape drive can be installed in the bottom shelf Installing a Tape Drive in the Bottom ShelfPage Configuring non-Plug and Play ISA Accessory Boards Installing Accessory BoardsConfiguring Accessory Boards with Plug and Play Installing the Board Installing an Accessory Board refer to facing Installing a BNC Coax Adapter Remove the metal plug Remove the nut To Install a BNC Coax AdapterInstalling an OverDrive Processor Processor Cables and power cordsInstalling the Security Bracket Troubleshooting Your PC HP Summary Screen Solving ProblemsIf Your PC Does Not Start Properly Display is Blank and There Are No Error MessagesCorrectly installed If You Cannot Start Your PC from a Modem If a Post Error Message is DisplayedClear the configuration Clearing the PC’s Configuration MemoryIf You Cannot Turn Off Your PC If Your PC Has a Hardware ProblemDisplay Does Not Work Properly If Your Display is Blurred or UnreadableIf Nothing is Displayed on the Screen Other Display ProblemsIf Your Mouse Does Not Work If Your Keyboard Does Not WorkEnsure that the keyboard is correctly connected Ensure that the mouse is correctly connectedIf Your Printer Does Not Work If the Flexible Disk Drive Does Not Work If the Hard Disk Does Not Work If the Hard DiskNot Work Cable connections or jumper settings If the CD-ROM Drive Has a ProblemCD-ROM Drive Does Not Work CD-ROM Drive is IdleIf an Accessory Board Does Not Work If You Have Forgotten Your Password If Your PC Has a Software ProblemIf the Date and Time are Incorrect If You Have a Network ProblemIf Your Application Software Does Not Work No Sound When Running Any Applications If Your PC Has an Audio ProblemSounds MS-DOS Games Give Not enough memory ErrorsChanging the Battery Strip supplied External battery as followsCable to the battery connector on the system board Technical Information System Board SwitchesBus Switch1 All measurements are in watts rms Power ConsumptionIRQs, DMAs, and I/O Addresses Used by Your PC Integrated Video Graphic Information HP Setup ProgramHewlett Packard Support and Information Services Introduction Service Means of AccessHP SupportPack Your HP Authorized ResellerRegion Phone Number Fax Number HP Support Assistant CD-ROMAt the CompuServe ! prompt, type GO HP Hewlett-Packard Information ServicesHP Forum on CompuServe HP Forum on America Online HP World Wide Web Site HP BBS LibraryCountry Number Baud Rate World-Wide Web URLHP FAXback on Demand-HP First Access MethodHP Audio Tips USA only HP Automated Support Directory Country/RegionAustralia Asia Pacific Ordering Drivers and Bios on DisketteEurope HP Support Services Customer Support Center Hewlett-Packard Telephone SupportNumber is +1 970 Country1 Language Local NumberNumber Method of Payment Charge Type Lifeline Telephone SupportHP Network Phone-in Support Service NPS Covered Time Available From SummaryAsia Hewlett-Packard Marketing HeadquartersPage Glossary Glossary Computer is running as an unattended network server From reflecting back along the cable Index LAN IndexRegulatory Information and Warranty Regulatory Information FCC for USA only Noise Declaration for Germany HP Hardware Warranty Customer Responsibilities HP Software Product License Agreement HP Software Product Limited Warranty Your HP Vectra PC Physical Characteristics Part Number D4550-90001