Throttle and choke cables, lever bearings | Husqvarna ProFlex 21

LUBRICATION

9.Throttle and choke cables, lever bearings

PF 18

Remove the right side cover on the lever housing (3 screws) and open the engine cover. Lubricate the cables’ free ends with the oil can, even those by the carburettor. Move the controls to the end points and lubricate again.

Lubricate the joints, catches, and bearings for the cutting unit’s control levers with an oil can.

Note risk for incorrect assembly: The ﬁne threaded screw on the side cover should be ﬁtted from the outside.

Replace the lever housing’s side cover.

PF 21

Remove the right side cover on the lever housing (2 screws) and open the engine cover. Lubricate the cables’ free ends with the oil can, even those by the carburettor. Move the controls to the end points and lubricate again.

Lubricate the joints, catches, and bearings for the cutting unit’s control levers with an oil can.

Replace the lever housing’s side cover.

6020-050

PF 18

8009-157

PF 18

8009-349

PF 21

8009-178

PF 21

English-67

Image 69

Husqvarna ProFlex 21 manual Throttle and choke cables, lever bearings

Contents

Rider ProFlex 18 Rider ProFlex Svenska Operator’s Manual for Rider ProFlex 18 and ProFlex Contents Important Information Introduction Introduction Serial Number Proper Service Symbols and decals Explanation of Symbols Xxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx Safety Instructions Safety instructionsGeneral use Keep children away from the work area Do not drive down slopes with the unit raised Do as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Presentation Presentation Placement of Controls Throttle Control Choke LeverAccelerator Accessories Lights and power outletCutting unit Lever for hydraulic lift of attachments, PF Cutting height adjustment leverLifting the cutting unit transport position Lowering the unit mowing position Mechanical lifting lever for cutting unit Transport positionMowing position Parking brake SeatFuelling Differential lock, PF Clutch controlChronometer Mowing tips Driving Before Starting DrivingStarting the engine Impaired cooling of the engine. Risk of major engine damage Do not run the starter motor for more than Driving the Rider, PF Stopping the engine, PF English-26 English-27 English-28 Maintenance MaintenanceMaintenance schedule = Described in this manual = Not described in this manual English-31 Engine cover Removing the Rider’s coversFront cover Right-hand wing cover Left-hand wing cover Checking the engine’s cooling air intakeTransmission cover Checking the transmission air intake Cleaning the engine and mufﬂer Checking and adjusting the steering cables Checking and adjusting the throttle cable Checking and adjusting the choke cableAdjusting the differential lock, PF Cable holder Adjusting the hydrostatic transmission cable Poorly adjusted brake can result in reduced braking ability Adjusting the parking brake Replacing the air ﬁlter, PF Replacing the air ﬁlter English-40 English-41 Cleaning the pulse air ﬁlter Replacing the fuel ﬁlterChecking the fuel pump’s air ﬁlter Checking the tyre pressures Checking the battery acid levelIgnition system Wrong spark plug type can damage the engine Replacing the spark plug Fuses Checking the safety system Replacing the light bulbs Cutting unit components Attaching the cutting unitExercise caution Risk of crush injuries Watch your ﬁngers. Do not turn the blades or the belt Check that the belt is around the idler Belt Sketch Parallelism Cutting height Placing in the service position Cutting unit’s service positionReleasing the service position Ground pressure Checking the blades Cutting unit model Exercise caution. Risk of crush injuries Removing the cutting unit Pull out the unit so that it catches on the outer hooks Removing the belt Removing the unit frame Hook the spring to the blade brake Attaching the belt Changing the cutting unit’s belt Removal of BioClip Plug Lubrication LubricationLubrication schedule, PF English-60 Lubricating the cables General Pedal mechanism in frame tunnel Lubricating in accordance with the lubrication schedule Differential lock cable, PF Chains in the frame tunnel Oil is topped up through the hole the dipstick sits Engine oil Replacing the engine oil Gear lever TransmissionDriver’s seat Throttle and choke cables, lever bearings Oil ﬁlter, change Hydraulic oil ﬁlter, change, PF Transmission oil level Parking Brake Cable English-70 Trouble Shooting Trouble Shooting GuideProblem Cause English-72 Storage StorageWinter Storage Service Electrical system Electrical and Hydraulic Systems English-76 Hydraulic system, PF English-78 Technical data Technical Data Data Rider ProFlex Hydraulic System TransmissionCutting unit Combi EU Declaration of Conformity EU Declaration of ConformityEU Declaration of Conformity only applies to Europe ProFlex 18 01/901/009 ProFlex 21 01/901/010 English-82 Service journal Service JournalAction After the First 8 Hours Action Date, mileage reading, stamp Signature Hour Service English-85 English-86 English-87 English-88 Action Date, mileage reading, stamp, signature English-90 Svenska ´z+H6T¶68¨ Svenska 114 02