EU Declaration of Conformity | Husqvarna ProFlex 21 specs

EU DECLARATION OF CONFORMITY

EU Declaration of Conformity

EU Declaration of Conformity (only applies to Europe)

We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that Rider Husqvarna Rider ProFlex 18 and ProFlex 21 dating from 2002 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:

-of June 22, 1998 “relating to machinery” 98/37/EC, annex IIA.

-of May 3, 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements. -of May 8, 2000 “relating to the emission of noise to surroundings” 2000/14/EC.

Information regarding noise emissions and the cutting width, see Technical Data.

The following harmonised standards have been applied: EN292-2, EN836.

The registered body 0404, SMP Svensk Maskinprovning AB, Fyristorgsgatan 3, SE-754 50 Uppsala, Sweden has issued the report with number

ProFlex 18: 01/901/009

ProFlex 21: 01/901/010

regarding the assessment of conformity according to annex VI to the COUNCIL’S DIRECTIVE of May 8, 2000 “relating to the emission of noise to surroundings” 2000/14/EC.

Huskvarna, January 3, 2002

Roger Andersson, Development Manager/Garden Products

English-81

Image 83

Husqvarna manual EU Declaration of Conformity only applies to Europe, ProFlex 18 01/901/009 ProFlex 21 01/901/010

Contents

Rider ProFlex 18 Rider ProFlex Svenska Operator’s Manual for Rider ProFlex 18 and ProFlex Contents Important Information Introduction Introduction Serial Number Proper Service Symbols and decals Explanation of Symbols Xxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx General use Safety InstructionsSafety instructions Keep children away from the work area Do not drive down slopes with the unit raised Do as follows Driving on slopes Children Maintenance Do not smoke when carrying out maintenance Transport Presentation Presentation Placement of Controls Accelerator Throttle ControlChoke Lever Cutting unit AccessoriesLights and power outlet Lowering the unit mowing position Cutting height adjustment leverLever for hydraulic lift of attachments, PF Lifting the cutting unit transport position Mowing position Mechanical lifting lever for cutting unitTransport position Fuelling Parking brakeSeat Chronometer Differential lock, PFClutch control Mowing tips Driving Impaired cooling of the engine. Risk of major engine damage DrivingBefore Starting Starting the engine Do not run the starter motor for more than Driving the Rider, PF Stopping the engine, PF English-26 English-27 English-28 Maintenance schedule MaintenanceMaintenance = Described in this manual = Not described in this manual English-31 Right-hand wing cover Removing the Rider’s coversEngine cover Front cover Transmission cover Left-hand wing coverChecking the engine’s cooling air intake Checking the transmission air intake Cleaning the engine and mufﬂer Checking and adjusting the steering cables Adjusting the differential lock, PF Checking and adjusting the throttle cableChecking and adjusting the choke cable Cable holder Adjusting the hydrostatic transmission cable Poorly adjusted brake can result in reduced braking ability Adjusting the parking brake Replacing the air ﬁlter, PF Replacing the air ﬁlter English-40 English-41 Checking the fuel pump’s air ﬁlter Cleaning the pulse air ﬁlterReplacing the fuel ﬁlter Wrong spark plug type can damage the engine Checking the battery acid levelChecking the tyre pressures Ignition system Replacing the spark plug Fuses Checking the safety system Replacing the light bulbs Exercise caution Risk of crush injuries Cutting unit componentsAttaching the cutting unit Watch your ﬁngers. Do not turn the blades or the belt Check that the belt is around the idler Belt Sketch Parallelism Cutting height Ground pressure Cutting unit’s service positionPlacing in the service position Releasing the service position Checking the blades Cutting unit model Exercise caution. Risk of crush injuries Removing the cutting unit Pull out the unit so that it catches on the outer hooks Removing the belt Removing the unit frame Hook the spring to the blade brake Attaching the belt Changing the cutting unit’s belt Removal of BioClip Plug Lubrication schedule, PF LubricationLubrication English-60 Lubricating the cables General Pedal mechanism in frame tunnel Lubricating in accordance with the lubrication schedule Differential lock cable, PF Chains in the frame tunnel Oil is topped up through the hole the dipstick sits Engine oil Replacing the engine oil Driver’s seat Gear leverTransmission Throttle and choke cables, lever bearings Oil ﬁlter, change Hydraulic oil ﬁlter, change, PF Transmission oil level Parking Brake Cable English-70 Problem Cause Trouble ShootingTrouble Shooting Guide English-72 Winter Storage StorageStorage Service Electrical system Electrical and Hydraulic Systems English-76 Hydraulic system, PF English-78 Technical data Technical Data Cutting unit Combi Data Rider ProFlex Hydraulic SystemTransmission ProFlex 18 01/901/009 ProFlex 21 01/901/010 EU Declaration of ConformityEU Declaration of Conformity EU Declaration of Conformity only applies to Europe English-82 After the First 8 Hours Service JournalService journal Action Action Date, mileage reading, stamp Signature Hour Service English-85 English-86 English-87 English-88 Action Date, mileage reading, stamp, signature English-90 Svenska ´z+H6T¶68¨ Svenska 114 02