Integra DTR-5.2 appendix Ir In/Out, Ac Inlet, 12V TRIGGER terminal, Connections, Monitor Out

Connections

If the device has a digital output jack as well, be sure to also connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the DTR-5.2 depending on the type of connector on the device.

With the initial settings of the DTR-5.2, the VIDEO 1 input source is set for digital input at the COAXIAL 2 jack.

If the digital connection is made at a different jack, this must be changed at the setup menu: Input Setup → Audio Setup → Digital Input (see page 29).

6.Connecting a satellite tuner, television, or settop box (VIDEO 2/3)

If the device is equipped with an S video output terminal, connect it to the S VIDEO 3 IN terminal with an S video cable. If it does not have an S video output terminal, connect its video output terminal to the VIDEO 3 IN terminal using an RCA-type video connection cable. You do not need to connect to both the S VIDEO 3 IN and VIDEO 3 IN terminals.

Using an RCA-type audio connection cable, connect the audio output terminal on the satellite tuner or television to the same VIDEO 3 IN audio jack on the DTR-5.2. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device have a digital output jack as well, be sure to also connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the DTR-5.2 depending on the type of connector on the device.

With the initial settings of the DTR-5.2, the VIDEO 3 input source is set for digital input at the OPTICAL 2 jack.

If the digital connection is made at a jack different from the initial settings, this must be changed at the setup menu: Input Setup → Audio Setup → Digital Input (see page 29).

You can also connect the device to the VIDEO 2 IN input jacks on the DTR-5.2 just like you can to the VIDEO 3 IN input jacks.

With the initial settings of the DTR-5.2, the VIDEO 2 input source is set for no digital input.

If you connect the device to the DIGITAL Input terminal, then this input source must be set for digital input at the setup menu: Input Setup → Audio Setup → Digital Input (see page 29).

7.Connecting a television monitor or projector

(MONITOR OUT)

If the monitor or projector is equipped with an S video output terminal, connect it to the MONITOR OUT S VIDEO terminal with an S video cable. If it does not have an S video output terminal, connect its video output terminal to the MONITOR OUT VIDEO terminal using an RCA-type video connection cable. You do not need to connect to both the MONITOR OUT S VIDEO and MONITOR OUT VIDEO terminals.

RS 232

The RS 232 port is to be used in conjunction with an external controller to control the operation of the DTR-5.2 by using an external device.

IR IN/OUT

If the DTR-5.2 is located inside a rack or cabinet that will not allow infrared beams to reach the IR sensor, you will need to connect a remote sensor to IR IN input to be able to use the remote controller. Then install the remote sensor in an unblocked location where you can easily point the remote controller.

Using a mini-jack connector, connect the IR emitter to the IR OUT terminal on the DTR-5.2 and then place the IR emitter on the remote sensor of the component or facing it.

AC INLET

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

AC INLET

Power cord (supplied)

To an AC wall outlet

•Do not use a power cord other than the one supplied with the DTR-5.2. The power cord supplied is designed for use with the DTR-5.2 and should not be used with any other adevice.

•Never have the power cord disconnected from the DTR-5.2 while the other end is plugged into the wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet first.

12V TRIGGER terminal

This terminal is provided so that you can use the operation of the DTR-5.2 control the operation of another externally connected device. Connect the component to this 1/8-inch mini-jack terminal and when the set input source is selected, the device will turn on. Set the 12V TRIGGER terminal using the 12V Trigger setting of the Input Setup [31].

13