Integra DTR-5.2 appendix Input Setup, Audio Setup procedure, Listening Mode Preset

Input Setup

2. Input Setup

These settings can be set differently for each input source.

Audio Setup

Digital Input (D. INPUT): This setting tells the DTR-5.2 which input source button on the front panel is connected with which digital input jack on the rear panel.

If you have connected your components in accordance with the default settings (given in the table below), then there is no need to change this setting.

Multichannel (MULTICH): This setting will not appear if AM or FM is selected at the front panel for the input source. The initial settings are “YES” for the DVD input source and “NO” for all other input sources. This setting is normally set to “NO,” and only needs to be changed to “YES” if a DVD player, MPEG decoder, or other component that has a multi channel port is connected to the MULTI CHANNEL INPUT port for 5.1-channel audio.

2.Press the Setup (SETUP) button.

Turn the jog dial or press the and cursor buttons on the remote controller to display “2. INPUT SETUP.”

3.Press the jog dial or ENTER button on the remote controller.

“AUDIO SETUP?” appears in the front display.

4.Press the jog dial or ENTER button on the remote controller.

The name of the digital input currently assigned to the selected input source appears.

Setup

DSP/Mode ADJ

Push To Enter

DSP/Mode ADJ

Push To Enter

DSP/Mode ADJ

Push To Enter

Default setting

Input source	Digital input	Multichannel
DVD	COAX 1	YES
VIDEO 1	COAX 2	NO
VIDEO 2	----	NO
VIDEO 3	OPT 2	NO
TAPE	----	NO
FM
AM
PHONO	----	NO
CD	OPT 1	NO
----: No setting	: Not applicable

OPT1: Select if connected to DIGITAL INPUT (OPTICAL) 1.

OPT2: Select if connected to DIGITAL INPUT (OPTICAL) 2.

COAX1: Select if connected to DIGITAL INPUT (COAXIAL) 1.

COAX2: Select if connected to DIGITAL INPUT (COAXIAL) 2.

5.Turn the jog dial or press the or cursor button on the remote controller to select the digital input.

(Example: If connected to COAX 1.)

6.Press either the jog dial or the cursor button on the remote controller.

“MULTICH=YES” or “NO” appears.

If a component with a 5.1-channel output terminal is connected (i.e., DVD player or MPEG decoder), turn the jog dial or press the and buttons on the remote controller to select “YES.”

DSP/Mode ADJ

Push To Enter

DSP/Mode ADJ

Push To Enter

DSP/Mode ADJ

Push To Enter

----:Select if the input source is not from a digital input jack.

Notes:

•Do not assign a digital input to more than one input source. If you are making a digital connection that requires you to change the default settings, be sure to always first cancel the current digital input setting and then assign the new setting.

•When playing a device that is actually connected to the MULTI CHANNEL INPUT terminal, select MULTICH with the Audio Selector button (see page 27).

Audio Setup procedure

1. Select the desired input source.

DTR-5.2

DVD Video 1 Video 2 Video 3 Tape FM AM Phono C D

VCR

Remote controller

7. Press the Return (RETURN) button.	Return
“AUDIO SETUP?” appears in the front
display.
To exit the setup mode immediately, press	Setup
the Setup (SETUP) button.

Listening Mode Preset

With the DTR-5.2, you can set a different listening mode for each different signal type that comes from each input source.

For example, with the default settings, even when using the same DVD player, if a CD is played, the listening mode automatically becomes “STEREO,” and if a DVD is played (Dolby Digital 3/2.1), the listening mode automatically becomes Dolby D.

Analog/PCM Source: Set a listening mode for the input signal from

2-channel analog sources and PCM source (default: STEREO.)

Note:

For PCM sources recorded at a sampling rate of 96 kHz or greater, only the Stereo or Direct listening modes can be selected. However, the set listening mode is stored in memory.

Digital format Source: Set a listening mode for the input signal

from digital sources (default: SURROUND).

29