Speaker setup
Speaker Distance
These settings tell the
Level Calibration
These settings allow you to set the volume levels of each speaker individually so that they all sound at the same level when heard from the listening position. If you are continuing from setting the speaker distances and are still in the setup mode, skip directly to step 2.
Setup
1. | Press the Setup (SETUP) button. | ||
| If anything other than “1. SPEAKER SETUP” | ||
| appears, turn the jog dial or press the and | ||
| cursor buttons on the remote controller until “1. | ||
| SPEAKER SETUP” appears. | ||
|
|
| |
|
|
|
|
2. | Press the jog dial or the ENTER button |
Setup
DSP/Mode ADJ
Push To Enter
DSP/Mode ADJ
1.Press the Setup (SETUP) button.
If anything other than “1. SPEAKER SETUP” appears, turn the jog dial or press the and cursor buttons on the remote controller until “1. SPEAKER SETUP” appears.
2.Press the jog dial or the ENTER button on the remote controller.
DSP/Mode ADJ
Push To Enter
DSP/Mode ADJ
on the remote controller. |
Push To Enter
Then turn the jog dial | or press the cursor | ||
button on the remote | controller to display | ||
“SPEAKER DISTANCE.” | |||
|
| ||
|
|
|
|
3. Press the jog dial or the ENTER button | |||
on the remote controller. |
Push To Enter
DSP/Mode ADJ
Push To Enter
DSP/Mode ADJ
Push To Enter
Then turn the jog dial or press the cursor button on the remote controller to display the “LEVEL CAL.”
3. Press the jog dial or ENTER button on |
the remote controller. |
A test sound (pink noise) will be heard from the |
left front speaker. At this point, it is not |
necessary to adjust the volume of the test |
sound. |
DSP/Mode ADJ
Push To Enter
DSP/Mode ADJ
Push To Enter
Then turn the jog dial or press the and
DSP/Mode ADJ
cursor buttons on the remote controller to select the unit of measurement.
Push To Enter
FEET: Select if you will enter the distances in feet.
METERS: Select if you will enter the distances in meters.
dB
4. Press either the jog dial or the |
cursor button on the remote controller |
again. |
The test sound will now be heard from a |
DSP/Mode ADJ
Push To Enter
4.Press the jog dial or the cursor button on the remote controller.
Then turn the jog dial or press the and cursor buttons on the remote controller to set the distance from the front speakers to the listening position.
DSP/Mode ADJ
Push To Enter
DSP/Mode ADJ
Push To Enter
different speaker. |
5. Turn the jog dial or press the or |
cursor buttons on the remote |
controller to adjust the volume of the |
test sound from this speaker to the |
same level that you heard from the |
previous speaker. |
DSP/Mode ADJ
Push To Enter
You can adjust the level in the range between
ft
You can set the distance in the range of 1 feet (0.3 m) - 30 feet (9 m) in 1 feet (0.3 m) steps.
5.Repeat the procedure in step 4 to set the distance from the center speaker (CENTER) and the surround speakers (SURR L/R) to the listening position.
6. Press the Return (RETURN) button. | Return |
You return to the “SP DISTANCE?” display.
Notes:
•If you press the Return (RETURN) button again, you go back up one more level.
•To exit the setup mode immediately, press the Setup (SETUP) button.
6.Repeat the procedure in step 4 and 5 until the volume of the test sound from all speakers is the same level.
Each time you press the jog dial or the button on the remote
controller, the test sound will be heard from a different speaker. The speaker order for calibration is LEFT (front left) → CENTER (center) → RIGHT (front right) → SURR RIGHT (surround right) → SURR LEFT (surround left) → SUBWOOFER (subwoofer).
7. Press the Return (RETURN) button. | Return |
You return to the “LEVEL CAL?” display.
Notes:
•If you press the Return (RETURN) button again, you go back up one more level.
•To exit the setup mode immediately, press the Setup (SETUP) button.
You can also press the TEST button on the remote controller to perform the Level Calibration setting. For more details, see page 9.
22