Manuals / Intel / Computer Equipment / Computer Hardware

Intel AI5VG user manual Typematic Rate Setting, Typematic Rate Chars/Sec, Typematic Delay Msec

Models: AI5VG

1 57

Download 57 pages 62.48 Kb

Page 43

Typematic Rate Setting

Chapter 7 LANDesk User Guide

Typematic Rate Setting

When disabled, continually holding down a key on your keyboard will generate only one instance. When enabled, you can set the two typematic controls listed next. By default, this field is set to Disabled.

Typematic Rate (Chars/Sec)

When the typematic rate is enabled, the system registers repeated keystrokes speeds. You can select speed range from 6 to 30 characters per second. By default, this item is set to 6.

Typematic Delay (Msec)

When the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec.

Security Option

This field allows you to limit access to the System and Setup. The default value is Setup. When you select System, the system prompts for the User Password every time you boot up. When you select Setup, the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up.

PCI/VGA Palette Snoop

Some non-standard VGA display cards may not show colors properly. This field allows you to set whether MPEG ISA/VESA VGA Cards can work with PCI/VGA or not. When this field is enabled, a PCI/VGA can work with a MPEG ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.

OS Select for DRAM > 64MB

This option allows the system to access greater than 64MB of DRAM memory when used with OS/2 that depends on certain BIOS calls to access memory. The default setting is NON-OS/2.

Video BIOS Shadow

This item allows you to change the Video BIOS location from ROM to RAM. Video Shadow will increase the video speed.

C8000 - CBFFF Shadow/DC000 - DFFFF Shadow

Shadowing a ROM reduces the memory available between 640KB to 1024KB. These fields determine whether optional ROM will be copied to RAM or not.

AI5VG Pentium VP3 Baby AT Motherboard User’s Manual

39

Image 43

Intel AI5VG Typematic Rate Setting, Typematic Rate Chars/Sec, Typematic Delay Msec, Security Option, PCI/VGA Palette Snoop

Contents

User’s Manual AI5VGPentium VP3 Baby AT Motherboard Page Chapter 4 Hardware Settings ContentsChapter 6 BIOS Configuration •Hardware Description •Hardware Settings ChecklistChapter 1 Introduction •Introduction •SpecificationsMain Memory Chapter 2 SpecificationsMain Processor L2 CacheWindows 95 Shut-Down BIOSOnboard Bus Mastering EIDE CPU Temperature SensorChapter 3 Hardware Description Chapter 3 Hardware Description Figure 1: Layout of the AI5VG MotherboardChapter 3 Hardware Description 3.1 Processor and CPU Voltage3.2 L2 Cache Memory 3.3 Main MemorySIMM1, SIMM2 Bank0Bank1 Total MemoryTotal Memory 3.4 BIOSBank0 DIMM2 Bank1 DIMM13. Power Management 3.5 Onboard PCI EIDE3.6 Onboard Multi-I/O 3.7 Onboard CPU Temperature SensorDevice Description 3.8 I/O Port Address Map3.9 DMA Channels AddressFunction 3.10 Interrupt Request Lines IRQ3.11 Accelerated Graphics Port AGP Slot LevelChapter 4 Hardware Settings Chapter 4 Hardware Settings Figure 2: Jumper Locations of the AI5VGP55C = Pentium with MMX technology Bus ClockMutiplier CPU FREQBus Clock Bus ClockMutiplier CPU FREQBus Clock 4.2 SW21-4:CPU Voltage SelectorFor Dual Voltage CPU Intel P55C, Cyrix 6x86L/MX, AMD K63.3V Function 4.3 JP5: Clear CMOS SelectionFunction Chapter 5 Installation Chapter 5 Installation Figure 3: Connector Location on the AI5VGWire Color 5.1 I/O ConnectorsFigure 4: Orientation of the I/O Connector 5.2 J3: AT Power Supply ConnectorSignal Name 5.3 J2: ATX Power Supply Connector5.4 J1, J4: AT Keyboard and PS/2 Mouse Connectors Signal NameSignal Name 5.6 J8: Floppy Drive Connector5.5 J7, J6: Serial Ports Signal NameSignal Name 5.7 J9, J11: EIDE ConnectorsJ9: Primary IDE Connector Signal NameSignal Name 5.8 J10: Parallel Port Connector5.9 J15: IrDA Connector 5.10 J5: USB ConnectorPin # Signal Name 5.11 J13 Wake on LAN Connector5.12 J14: CPU Fan Power Connector 5.13 J20 Front Bezel ConnectorSignal Name Speaker: Pins 1 -Signal Name Power LED and Keylock: Pins 11 -Signal Name Reset Switch: Pins 9 andJ20 Pin # Chapter 6 BIOS Configuration Cache Rd+CPU Wt Pipeline IDE Primary/Secondary Master/Slave PIO 6.2 BIOS Setup 6.1 BIOS IntroductionPress <DEL> to Enter Setup Chapter 7 LANDesk User Guide STANDARD CMOS SETUPDate 6.3 Standard CMOS SetupHEAD TimePrimary HDDs / Secondary HDDs CYLSHalt On Drive A / Drive BFloppy 3 Mode Support VideoVirus Warning 6.4 BIOS Features SetupCPU Internal Cache / External Cache Boot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Delay Msec Typematic Rate SettingVideo BIOS Shadow Typematic Rate Chars/SecSustained 3T Write 6.5 Chipset Features SetupBank DRAM Timing DRAM Read PipelineMemory Hole at 15MB Addr Video BIOS CacheableSystem BIOS Cacheable Cache TimingPower Management 6.6 Power Management SetupModem Use IRQ HDD Power DownPM Control by APM Video Off MethodChapter 7 LANDesk User Guide PM EventsResources Controlled by 6.7 PNP/PCI ConfigurationPNP OS Installed Reset Configuration DataPCI Master 0 WS Write PCI#2 Access #1 RetryCPU to PCI Write Buffer PCI Dynamic BurstingChapter 7 LANDesk User Guide PCI IDE IRQ Map To6.9 Load Setup Defaults 6.8 Load BIOS DefaultsChapter 7 LANDesk User Guide IDE HDD Block Mode 6.10 Integrated PeripheralsOnChip Primary/Secondary PCI IDE IDE Prefetch ModeUART 2 Mode IDE Primary/Secondary Master/Slave UDMAOnboard FDD Controller Onboard Serial/Parallel PortChapter 7 LANDesk User Guide 6.11 Supervisor / User Password6.13 HDD Low Level Format 6.12 IDE HDD Auto DetectionChapter 7 LANDesk User Guide 6.15 Exit Without Saving 6.14 Save & Exit SetupChapter 7 LANDesk User Guide