Driver Installation for Display Adapter Windows | Intel ECB-865

ECB-865

5.2Driver Installation for Display Adapter

5.2.1Windows 9x

The following steps will install the display driver for the ‘Chips & Technologies 69000 PCI’ display controller.

1.Click the ‘Start’ button on the task bar, select ‘Settings’ and ‘Control Panel’ from the sub-menu. This should start the Control Panel as shown below:

2. Double click the ‘Display’ icon and select the ‘Settings’ tab as shown below.

ECB-865 User’s Manual 79

Image 89

Intel ECB-865 user manual Driver Installation for Display Adapter Windows

Contents

User’s Manual ECB-865 FCC Statement Trademark Acknowledgement Copyright NoticeDisclaimer Life Support Policy Message to the Customer Evalue Customer ServicesTechnical Support Evalue Technology Inc Evalue Europe A/S Product Warranty Packing List Manual Objectives Introduction Watchdog Timer Programming Jumper & Connector Entering Setup Setting JumpersConnector Definitions Map Revision Date Comment Document Amendment History Manual Objectives System Overview Introduction Chipset ITE IT8712F-A System Specifications Expansion Interface Mechanical and Environmental Weight 0.5 Kg Architecture Overview 1 82815 Gmch and 82801BA AGP Interface Dram InterfaceMultiplexed AGP and Display Cache Interface Ethernet 7.1 ICH2 LAN Controller PCI Interface6 USB Systems DiskOnChip IntelITE IT8712F-A Safety Precautions Hardware ConfigurationInstallation Procedure Main Memory Removing CPU Systems’ DiskOnChip Flash Disk Installing DOCExpansion Interface Installing the Single Board Computer 1 815E integrated Graphics Controller Drivers Support Enable WDT Watchdog Timer ProgrammingDisable WDT Re-trigger WDT Jumper & Connector Jumper & Connector Layout Jumpers Label Function Jumper & Connector ListJP10 JP11 J10 Connectors Label FunctionJ11 J12 Setting Jumpers Watchdog Timer Programming I/O Address Select JP6 Watchdog Timer Enable / Disable Onboard Watchdog Timer JP12Clear Cmos JP9 0553H / 0033H 0543H / 0343H Sec Watchdog Timer Time-Out Interval Select JP10JP10 16 Sec 32 Sec 64 Sec 10.3 COM2 RS-232/422/485 Select JP1, JP2~JP5 Bus Master Systems DiskOnChip Memory Address Select JP11Proprietary PCI Bus Master Selection JP13 External Speaker Connector J2 Connector Definitions System Reset Connector J1Keyboard Lock & Power Indicator Connector J3 Primary IDE / Secondary IDE Active Indicator Connector J4 Primary IDE Connector J5 Secondary IDE Connector J10 ECB-865 Primary Master connector STROBE, with the PIIX4 latching RESET# Floppy Connector J6 DRVDEN0/1# Signal Description Floppy Connector J6 Parallel Port Connector J11 ATX Power Button Connector J8 11.12 DB25 Parallel Port Connector J11 STB# Signal Description Parallel Port Connector J11 GND DTR CTS CTS RTS DSR GND CTS/RTS + Signal Description USB Connector J13, J19 USB Connector J13, J19CPU Fan and System Fan Connector J14, J25 Fast & Standard IrDA Connector J15 Smart Card Interface J17 Signal Configuration Fast & Standard IrDA Connector J15ATX Power Controller J16 Signal Description 10/100Base-Tx Ethernet Connector J18, J20 11.28 10/100 BASE-Tx Ethernet Connector J18, J20 Signal Description CRT Connector J22 CRT Connector J22 11.33 PS/2 Keyboard Connector J26 Internal Keyboard Connector J24Signal Description Int. & PS/2 Keyboard Connector J24, J26 11.35 PS/2 Mouse Connector J26 Proprietary PCI Connector J21 Write bursts System Interface Control Arbitration Error Reporting Interrupts Press F1 to Run Setup or Resume AMI Bios Setup Enter key to accept or enter the sub-menu AMI Bios Setup Main Menu Standard Cmos Setup Menu Cmos Setup Reference TableDate and Time Configuration Floppy A, Floppy B Master Disk, Slave Disk Boot Sector Virus Protection Quick Boot Advanced Cmos Setup Defaults Try Other Boot Device 2.2 1st / 2nd / 3rd Boot DeviceBootUp Num-Lock Password Check Shadow Memory from Address C000~DFFF, 16K Per Segment Boot To OS/2System Bios Cacheable CPU Ratio Selection Advanced Chipset Setup DefaultsICH Delayed Transaction Internal Graphic Mode Select Sdram RAS# to CAS# DelayMemory Hole Dram Cycle time SCLKs Power Management/ APM Power Management Setup DefaultsGreen PC Monitor Power State Acpi Aware O/S Stand by Time Out Minute CPU Critical TemperatureSuspend Time Out Minute Throttle Slow Clock Ratio Wake Up on LAN Power Button FunctionWake Up on Ring Plug and Play Aware O/S PCI / Plug and Play Setup Defaults Clear Nvram PCI Latency Timer PCI ClocksPCI / VGA Palette Snoop Allocate IRQ to PCI VGA OnBoard FDC Peripheral Setup DefaultsOnBoard Serial Port1 OnBoard Serial Port2 Parallel Port Mode DisabledOn Board Parallel Port 378h On-Chip IDE Parallel Port IRQParallel Port DMA Channel Hardware Monitor Setup Defaults User’s Manual Driver Installation for Ethernet Adapter Windows Driver Installation User’s Manual ECB-865 User’s Manual ECB-865 Windows NT 4.0 Ethernet Installation ECB-865 User’s Manual ECB-865 User’s Manual Driver Installation for Display Adapter Windows User’s Manual ECB-865 User’s Manual ECB-865 Windows NT 4.0 Display Installation ECB-865 User’s Manual ECB-865 Measurement Drawing Bios Rev New Features Bugs/Problems Solved Known Problems Appendix a Bios Revisions Memory Map Appendix B System Resources Port Description Map User’s Manual Interrupt Description Interrupt Usage DMA-channel Description DMA-channel Usage If it beeps… Then… Appendix C Amibios Power-On Self Test Code Description Appendix D Amibios Post Check Point List Bios User’s Manual Present User’s Manual ECB-865 User’s Manual