Manuals / Intel / Computer Equipment / Computer Hardware

Intel GA-N650SLI-DS4L user manual B. Configuring SATA controller mode in BIOS Setup, Step

Models: GA-N650SLI-DS4L

1 100

Download 100 pages 30.59 Kb

Page 76

B. Configuring SATA controller mode in BIOS Setup

B. Configuring SATA controller mode in BIOS Setup

Make sure to configure the SATA controller mode correctly in system BIOS Setup.

Step 1:

Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Under Integrated Peripherals, ensure NV Serial-ATA Controller is enabled. To enable all four SATA 3Gb/s connectors, set this item to All Enabled (Figure 1). SATA-1controls the SATAII0 and SATAII1 connectors only. To configure a RAID array, go to the SATA-II RAID Config submenu (Figure 2).

CMOS Setup Utility-Copyright (C) 1984-2007 Award Software

Integrated Peripherals

`	SATA-II RAID Config		[Press Enter]				Item Help
						Menu Level`
	On-Chip IDE Channel0		[Enabled]			Menu Level`
	IDE DMA transfer access		[Enabled]
	On-Chip MAC Lan		[Auto]
	Onboard LAN Boot ROM		[Disabled]
	NV Serial-ATA Controller		[All Enabled]
	IDE Prefetch Mode		[Enabled]
	On-Chip USB		[V1.1+V2.0]
	USB Keyboard Support		[Disabled]
	USB Mouse Support		[Disabled]
	Onboard Audio Function		[Auto]
`	SMART LAN		[Press Enter]
	Legacy USB storage detect		[Enabled]
	Onboard Serial Port 1		[3F8/IRQ4]
	Onboard Parallel Port		[378/IRQ7]
	Parallel Port Mode		[SPP]
x ECP Mode Use DMA			3
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save		ESC: Exit	F1: General Help
	F5: Previous Values		F6: Fail-Safe Defaults			F7: Optimized Defaults

Figure 1

Enable the SATA connectors with hard drives that you want to use for RAID. For example, SATA-II 1 Primary RAID is for the SATAII0 connector and SATA-II 1 Secondary RAID for the SATAII1 connector (Figure 2).

CMOS Setup Utility-Copyright (C) 1984-2007 Award Software

SATA-II RAID Config

	SATA-II RAID function		[Enabled]				Item Help
	SATA-II 1 Primary RAID		[Enabled]			Menu Level`
	SATA-II 1 Secondary RAID		[Enabled]
	SATA-II 2 Primary RAID		[Disabled]
	SATA-II 2 Secondary RAID		[Disabled]
	KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save		ESC: Exit	F1: General Help
	F5: Previous Values		F6: Fail-Safe Defaults			F7: Optimized Defaults
Step 2:			Figure 2
Save changes and exit BIOS Setup.

The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version.

GA-N650SLI-DS4L Motherboard

- 76 -

Image 76

Intel GA-N650SLI-DS4L user manual B. Configuring SATA controller mode in BIOS Setup, Step, Save changes and exit BIOS Setup

Contents

GA-N650SLI-DS4L Users ManualMotherboard GA-N650SLI-DS4L Oct. 15Motherboard GA-N650SLI-DS4LCopyright DisclaimerDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Chapter 1 Hardware Installation1-3-2 Installing the CPU Cooler 1-4-1 Dual Channel Memory ConfigurationChapter 3 Drivers Installation Chapter 4 Unique FeaturesConfiguring SATA Hard Drives Chapter 5 AppendixBox Contents Optional ItemsAUDIO PCIE162 GA-N650SLI-DS4LBlock Diagram Surround Center/Subwoofer SideChapter 1 Hardware Installation 1-1 Installation PrecautionsProduct Specifications x 24-pin ATX main power connector Adjust PCI Express x16 frequency from 100 MHz to 150 MHz with 1-3 Installing the CPU and CPU Cooler 1-3-1 Installing the CPUCPU Socket Lever Direction of the Arrow Sign on the Male Push Pin 1-3-2 Installing the CPU CoolerMale Push Pin The Top of Female Push Pin Female Push Pin 1-4 Installing the Memory 1-4-1 Dual Channel Memory Configuration1-4-2 Installing a Memory 1-5 Installing an Expansion Card press x16 slot to re1-6 Setup of an SLI Scalable Link Interface Configuration A. Before You Begin1. Understanding the SLI Configuration Jumpers Normal Mode Normal Mode Pins 2-3 Close, Default SettingB. Setting the SLI Configuration Jumpers C. Connecting Two Graphics Cardsconnector Female slots on the bridgePlace this section on the top of the bridge connector D. Configuring the Graphics Card DriverRetention Bracket 1-7 Back Panel Connectors Coaxial S/PDIF Out ConnectorOptical S/PDIF Out Connector PS/2 Keyboard and PS/2 Mouse PortCenter/Subwoofer Speaker Out Jack Orange Rear Speaker Out Jack BlackSide Speaker Out Jack Gray Line In Jack Blue1-8 Internal Connectors ATX12VFPANEL CPUFAN+5V Only for 2x12 pinATX 1/2 ATX12V/ATX 2x2 12V Power Connector and 2x12 Main Power Connector3.3VOnlyfor2x12pin ATX 3/4/5 CPUFAN/SYSFAN/PWRFAN Fan Headers 6 NBFAN North Bridge Fan HeaderCPUFAN PWRFAN7 FDD Floppy Disk Drive Connector 8 IDE1 IDE ConnectorSATAII3 SATAII0SATAII2 SATAII110 PWRLED System Power LED Header 11 BAT Battery12 FPANEL Front Panel Header 14 CDIN CD In Connector 13 FAUDIO Front Panel Audio Header16 SPDIFIN S/PDIF In Header 15 SPDIFO S/PDIF Out HeaderGA-N650SLI-DS4L Motherboard 17 FUSB1/FUSB2 USB Headers, Yellow 18 CI1 Chassis Intrusion Header19 CLRCMOS Clearing CMOS Jumper Open Normal Short Clear CMOS ValuesChapter 2 BIOS Setup A. The LOGO Screen Default 2-1 Startup ScreenB. The POST Screen DEL BIOS Setup/Q-FlashSample BIOS Version D1 BIOS Setup Program Function Keys2-2 The Main Menu Main Menu Help„ Standard CMOS Features „ Advanced BIOS Features„ Power Management Setup „ PnP/PCI ConfigurationsStandard CMOS Features DateTime IDE Channel 0 Master/SlaveDrive A Floppy 3 Mode SupportHalt on MemoryAdvanced BIOS Features Hard Disk Boot PriorityFirst/Second/Third Boot Device Password CheckLimit CPUID Max. to 3 Note No-Execute Memory Protect NoteCPU Enhanced Halt C1E Note CPU Thermal Monitor 2 TM2 NoteSATA-II RAID Config Integrated PeripheralsSATA-II RAID function SATA-II 1 Primary RAIDIDE DMA transfer access Onboard LAN Boot ROMSATA-II 2 Secondary RAID On-Chip IDE Channel0SMART LAN LAN Cable Diagnostic Function When No LAN Cable Is AttachedWhen LAN Cable Is Functioning Normally When a Cable Problem OccursLegacy USB storage detect Onboard Serial PortOnboard Parallel Port Parallel Port ModeACPI Suspend Type PME Event Wake UpModem Ring On USB Resume from SuspendPower-On by Alarm Power On By MousePower On By Keyboard KB Power ON Password2-7 PnP/PCI Configurations PCI 1 IRQ AssignmentPCI 2 IRQ Assignment BIOS auto-assigns IRQ to the first PCI slot. DefaultReset Case Open Status Current CPU/SYSTEM/POWER FAN Speed RPMCPU/SYSTEM/POWER FAN Fail Warning PC Health StatusCPU Smart FAN Mode CPU Smart FAN ControlSystem Smart FAN Control System Clock Setting MB Intelligent TweakerM.I.TFSB-Memory Clock Mode FSB-Memory RatioCPU Host Frequency Mhz Actual CPU Clock MhzDDR2 Voltage Control NB/HT-Link VoltageFSB Voltage South Bridge Voltage2-11 Load Optimized Defaults 2-10 Load Fail-Safe DefaultsLoad Optimized DefaultsSaveY/N?& ExitN Setup Set Supervisor/User Password 2-12Supervisor Password User Password2-13 Save & Exit Setup 2-14 Exit Without SavingGA-N650SLI-DS4L Motherboard Chapter 3 Drivers Installation 3-1 Installing Chipset Drivers3-2 Software Applications 3-3 Driver CD Information3-4 Hardware Information 3-5 Contact UsGA-N650SLI-DS4L Motherboard Chapter 4 Unique Features 4-1 Xpress Recovery2Before You Begin System RequirementsInstallation and Configuration A. Installing Windows XP and Partitioning the Hard Drive4. After the operating system is installed, right-click the My Computer icon on your desktop and select Manage Figure 4. Go to Computer Management to check disk allocation. Xpress Recovery2 will save the backup file to the unallocated space black stripe along the topFigure 5. Please note that if there is no enough unallocated space, Xpress Recovery2 cannot save the backup file B. Accessing Xpress Recovery2 C. Using the Backup Function in Xpress Recovery2E. Removing the Backup D. Using the Restore Function in Xpress Recovery2F. Exiting Xpress Recovery2 4-2 BIOS Update Utilities 4-2-1 Updating the BIOS with the Q-Flash UtilityWhat is Q-FlashTM? What is @BIOSTM?Copy BIOS completed - Pass B. Updating the BIOSPlease press any key to continue Step 4-2-2 Updating the BIOS with the @BIOS Utility B. Installing and Using @BIOSC. Options and Instructions 1. Save the Current BIOS File3. Update the BIOS without Using the Internet Update Function Click Update New BIOS4-3 EasyTune The EasyTune 5 Interface Button Information Table4-4 Windows Vista ReadyBoost Properties5-1 Configuring SATA Hard Drives 5-1-1 Configuring the Onboard SATA ControllerTo configure SATA hard drives, follow the steps below A. Installing SATA hard drives in your computerSave changes and exit BIOS Setup B. Configuring SATA controller mode in BIOS SetupStep C. Configuring RAID set in RAID BIOS AppendixTAB Navigate N New Array ENTER Detail R Rebuild5-1-2 Making a SATA RAID Driver Diskette cd bootdrv menu5-1-3 Installing the SATA RAID Driver and Operating System Press F6 if you need to install a third party SCSI or RAID driverS=Specify Additional Device ENTER=Continue F3=ExitENTER=Select F3=Exit S=Specify Additional Device Enter=Continue F3=ExitStep Appendix5-2 Configuring Audio Input and Output 5-2-1 Configuring 2/4/5.1/7.1-Channel AudioA. Configuring Speakers the function for each jack through the audio driverC. Configuring AC97 Audio B. Configuring Sound EffectSound Effect tab A. Installing the S/PDIF In Cable 5-2-2 Installing the S/PDIF In Cable OptionalS/PDIF In S/PDIF Out C. Configuring S/PDIF outB. Conneting a S/PDIF out Cable 5-2-3 Configuring Microphone Recording Select Realtek HD Audio Input in the Mixer device list Recording the Sound 5-2-4 Using the Sound RecorderPlaying the Sound 5-3 Troubleshooting 5-3-1 Frequently Asked Questions5-3-2 Troubleshooting Procedure Correctly insert theor cable might fail CPU or CPU socketThe graphics card T h e I D E / S A T AWEEE Symbol Statement Regulatory StatementsRegulatory Notices Our Commitment to Preserving the EnvironmentChina Restriction of Hazardous Substances Table GA-N650SLI-DS4L Motherboard Appendix GA-N650SLI-DS4L Motherboard Contact Us GIGABYTE Global Service System