Manuals / Intel / Computer Equipment / Computer Hardware

Intel 88ENEP3S00 user manual Driver Installation, Browse CD Exit

Models: 88ENEP3S00 Intel P35/P31 Socket LGA775 Processor Mainboard

1 45

Download 45 pages 48.95 Kb

Page 40

Chapter 5 Driver Installation

P3 Series	User's Manual

Chapter 5 Driver Installation

Check your package and there is Driver CD included. This CD consists of all dirvers you need. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which drivers needed so that your system can function properly.

Insert CD into your CD-ROM drive and the menu should appear as below. If the menu does not appear, double-click My Computer / double-click CD-ROM drive or click Start / click Run / type X:\AUTORUN.EXE (assuming X is your CD-ROM drive).

+Mainboard Driver installation Utility

+Userful Software Utility

> Browse CD

Exit

(This picture is only for reference)

From the Main MENU you may make 4 selections:

1.+Mainboard Driver installation Utility: Click to enter the driver installation menu.

2.+Useful Software Utility: Click to enter the utilities installation menu.

3.>Browse CD: Click to browse the contents of this “Driver & Utility CD”.

4.Exit: Click to exit this installation menu.

- 39 -

Image 40

Intel 88ENEP3S00 Driver Installation, + Mainboard Driver installation Utility + Userful Software Utility, Browse CD Exit

Contents

Intel P35/P31 P3 SeriesUser’s Manual Socket LGA775 Processor MainboardDisclaimer CopyrightTable of Contents Package ChecklistSpecifications Connecting Rear Panel I/O Devices1.1 Package Checklist Chapter 1 Introduction1.2 Specifications -1 For IP35-PRO 1.2 Specifications -2 For IP35-S Provides 6 x SATA high speed HDD ports Inclucding 4 x SATA through1.2 Specifications -3 For IP31-CF Integrated PortsThis picture is only for reference 1.3 Mainboard Layout -1 PCB Layout for IP35-PROBAKBIOS USRBIOS USRBIOS 1.3 Mainboard Layout-2 PCB Layout for IP35-SThis picture is only for reference 1.3 Mainboard Layout-3 PCB Layout for IP31-CF This picture is only for referenceSFAN2 JDDR11.4 Connecting Rear Panel I/O Devices Optional Debug LED COMAUDIO1 1.4 Connecting Rear Panel I/O Devices2.2 Installing Mainboard Chapter 2 Hardware Setup2.1 Choosing a Computer Chassis 2.3 Installation of the CPU and CPU Cooler 2.3.1 Installation of the CPU2.4 Installation of Memory Modules 2.3.2 Installation of the CPU Cooler2.5 Connecting Peripheral Devices 2.5.1 Floppy and IDE Disk Drive Connectors2.5.2 Serial ATA Connectors 2.5.3 PCI and PCI Express slotsChapter 3 Jumpers & Headers Setup 3.1 Checking Jumper Settings3.3 Keyboard Power FunctionJKB 3.2 CMOS Memory Clearing Header3.4 FAN Power Connectors 3.5 Front Panel Switches & Indicators HeadersRESET Reset Control PWR-ON Power Button3.6 Additional USB Port Headers 3.7 Front Panel Audio Connection HeaderFU,SB2/4/3/1 FAUDIO3.8 Internal Audio Connectors 3.9 ATX Power Input ConnectorsBAKBIOS USRBIOS BAKBIOS USRBIOSChapter 4 BIOS Setup Utility 4.1 About BIOS Setup4.2 To Run BIOS Setup 4.4 The POST Power On Self Test4.5 BIOS Setup - CMOS Setup Utility 4.5.1 CMOS Setup UtilityStandard CMOS Features Advanced BIOS FeaturesLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User Password4.5.3 Standard CMOS Features P3 SeriesUsers Manual ・ Date mmddyy Access Mode Back to Standard CMOS Features Setup Menu ・ Drive A & Drive B IDE HDD Auto-Detection IDE Channel 0 Master/Slave,SATA Channel 1~44.5.4 Advanced BIOS Features ・ Hard Disk Boot Priority・ Quick Power On Self Test ・ Virus Warning・ Boot Up Floppy Seek 4.5.5 Advanced Chipset Features ・ System BIOS Cacheable PCI-E Compliancy Mode ・ Memory Hole At 15M-16MIDE HDD Block Mode IDE DMA transfer access4.5.6 Integrated Peripherals OnChip IDE Device Back to Integrated Peripherals Setup Menu Onboard Device IDE Primary Master/Slave UDMA Auto On-Chip Secondary PCI IDE IDE Primary Master/Slave PIO Back to Integrated Peripherals Setup Menu Super IO Device Onboard FDC ControllerOnboard Serial Port BIOS Write Protect Parallel Port Mode EPP Mode Select ECP Mode Use DMA Back to Integrated Peripherals Setup Menu ・ KB Power ON Password・ Power Management ・ ACPI Function・ ACPI Suspend Type P3 Series・ Suspend Mode ・ HDD Power Down・ Power On by Ring ・ Resume by Alarm4.5.8 PnP PCI Configuration ・ Reset configuration data・ Init Display First ・ Resource controlled by・ FAN Mode Setting ・ Shutdown Temperature4.5.9 PC Health Status ・ Sensor Show On Post・ CPU Feature ・ CPU Clock Mode4.5.10 Frequency/Voltage Control ・ Ajust Cpu Voltage4.5.11 Load Fail-Safe Defaults 4.5.12 Load Optimized Defaults4.5.13 Set Supervisor/User Password Load Fail-Safe Defaults Y/N? N4.5.14 Save & Exit Setup 4.5.15 Exit Without SavingPASSWORD DISABLED！ Press any key to continue SAVE to CMOS and EXIT Y/N? Y+ Mainboard Driver installation Utility + Userful Software Utility Chapter 5 Driver InstallationBrowse CD Exit 1. Intel Chipset Installtion Utility 2. Marvell or Realtek LAN Driver Exit3. Realtek Audio Driver RealtekOnboardLAN DriverLAN DriverPOST Codes hex NameDescription APPENDIXinitialization. If not, execute ISA tests an clear EISA mode flag Initialize first 120 interrup tvectors with SPURIOUSINTHDLRVerify 8259 Channel 2 masked interrupts by alternately turning Turn off interrupts then verify no interrupt mask register is onTest base memory from 256K to 640K and extended memory If EISA Mode flag is set then test EISA memory found in slotsInitialize any serial and parallel ports also game port Reboot if Manufacturing POST Loop pin is set. Otherwise display any messages i.e., any non-fatal errors that weredetected during POST and enter Setup Ask password security optional