Manuals / Brands / Computer Equipment / Projector / JVC / Computer Equipment / Projector

JVC CB100 4.11.2. Connecting VIC Source Cables, Table 4.0-5 VIC Video Source Cable Connections, 4.11.3. VIC Editing

1 128

Download 128 pages, 1.35 Mb

Chapter 4—Setup Adjustments

HJT Model 100 User's Guide 4-41

4.11.2. Connecting VIC Source Cables

Connect the source cables to the input connectors as marked on the rear

of the VIC.

Table 4.0-5 VIC Video Source Cable Connections

VIC Input

Connectors Cable Connections

Wide Bandwidth

RGBHV Connect the RGBHV cables to the appropriately marked input jacks

(Figure 4.0-20 on page 4-44).

Graphics Enhancer

RGBHV Connect the RGBHV cables to the appropriately marked input jacks

(Figure 4.0-20 on page 4-44).

Quad RGBHV Video

Mux (multi-port) Connect the RGBHV cables to the input connectors on the port(s) t o be used

(Figure 4.0-21on page 4-44).

Component HDTV

(YPbPr) Input

Module

Connect the three (3) input cables to the appropriate input jacks

(Figure 4.0-22 on page 4-44).

NOTE: Red, Green, and Blue input jacks are in a different order from the

RGBHV VIC with Green at the left, Blue in the middle, and Red on the right.

The HDTV YPbPr VIC uses the same circuitry and input jacks to process

two (2) different type of inputs; the GBR input and the YPbPr input.

Only one (1) of these inputs may be selected at any one time.

The selection of one of these inputs is made by editing the second number in

the VIC column (see editing VICs following) and using separate channels

for their sources.

Quad Standard

Decoder Module

(with Line Doubler)

There are two (2) distinct input connections (Figure 4.0-23 on page 4-45).

The input connector at right, labeled Video is for Composite Video (C-VID).

The two (2) connectors at left, labeled Y and C are for S-Video.

The selection of one of these inputs is made by editing the second number in

the VIC column (see editing VICs, below) and using separate channels for

their sources.

4.11.3. VIC Editing

The VIC column in the CHANNELS MENU must now be edited so the

sources coming into the projector follow the correct path through the

correct VIC input.

To edit a VIC:

1. Select CHANNELS from the MAIN MENU.

2. Select a blank channel.

NOTE: If there are no blank channels, don't edit an existing channel

for a new VIC—press MODE and cut the entire channel entry and start

from a blank channel.

3. Press the MODE KEY to display the EDIT submenu.

4. Select EDIT.

5. Press the right arrow to move to the VIC column, then press ENTER.

Contents

Main DECLARATION OF CONFORMITY Table of Contents Safety Information Chapter 1. Introduction Chapter 2. Installation Chapter 3. Operation Chapter 4. Setup Adjustments Page Page Safety Information 0.1. Warnings and Cautions WARNING SYMBOL Warns user of a potential CAUTION SYMBOL W arns user of a potential 0.2. Installation Safeguards 0.3. Heat Safeguards 0.3.1. Fans and Ventilation 0.4. Light Safeguards 0.5. Electrical Safeguards 0.5.1. Power Supply Page 1.0 Introduction Page 1.1. Shipping and Inspection 1.2. Items Shipped with the HJT Model 100 Projector 1.3. Options 1.4. Projector Control 1.5. Right and Left Orientation Table 1.0-1 Acronyms Used In Manual Page 2.0 2.1. Air Flow and Maintenance Clearances 2.1.1. Air Flow Table 2.0-1 Air Flow Clearances 2.1.2. Maintenance Access 2.2. Physical Dimensions Figure 2.0-1 Top View M100 Projector (dimensions in mm) Page Figure 2.0-4 Front View M100 Projector (dimensions in mm) 2.3. Projector Orientation 2.4. Projector-to-Screen Distance and Alignment 2.5. Lens Throw Distance and Screen Width Table 2.0-3 Lens Definitions Table 2.0-4 Throw Distance Calculation Figure 2.0-7 Throw Distance vs Screen Width Illustration (3:1, 1:1 lenses) Figure 2.0-8 Lens Pattern for Model 100 2.6. Power Requirements Table 2.0-5 Power Sources 2.7. Signal Sources Connection Figure 2.0-9 Standard RGBHV and Optional HDTV Input Connections 2.7.1. Terminal or Remote Control 2.7.2. Infrared (IR) Windows 2.8. Sources 2.8.1. Types of Standard Composite Signals Table 2.0-6 Standard Composite Signals 2.8.2. Red, Green and Blue Analog Signals 2.8.2.1. Signal Inputs Page 3.0 Operation 3.1. Executive Remote Page 3.2. Technician Remote Page Chapter 2Installation HJT Model 100 User's Guide 3-5 Table 3.0-1 Remote Control Key Functions Key Function Usage 3.3. Power ON and OFF CAUTION!!! Before applying power to the projector thoroughly read the safety guidelines outlined at the beginning of this operators manual. 3.4. Displaying Internal Test Patterns Table 3.0-2 Internal Test Patterns #Description Purpose 3.5. Displaying External Signals Table 3.0-3 On-Screen Factory-Preset Channel Menu Display Table 3.0-4 Factory-Preset Channels Menu Display Definitions Table 3.0-5 Source Menu 3.5.1. Internal Source 3.6. Navigating the Menu 3.6.1. Displaying the Main Menu 3.6.2. Choosing Numbered Menus 3.6.3. To Choose Full or Short Menus 3.6.4. Menu Selection Examples HJT Model 100 User's Guide 3-11 Figure 3.0-3 Menu Structure Diagram 3.7. Full Menu Structure Table 3.0-6 Channel and Source Definitions 3.8. Selecting a Channel 3.8.1. Active Channel Figure 3.0-4 Channel List with Active Channel and Source 3.9. Attaching a Source Page Figure 3.0-5 Active and Highlighted Sources 3.10. Picture Settings 3.11. Menu Item Definitions Table 3.0-7 Available Menu Items Page Page Page HJT Model 100 User's Guide 3-21 3.12. Short Menu Structure Figure 3.0-6 Short Menu Tree 3.13. PC or VT-100 Terminal Control 3.13.1. Terminal Preferences Table 3.0-8 Terminal Preferences 3.13.2. Communications Protocol Table 3.0-9 Communication Protocol Table 3.0-10 VT-100 Terminal and Remote Command Equivalents Page 4.0 Setup Adjustments 4.1. Setup Preparation Table 4.0-1 Setup Phrases, Definitions, and General Information Page Page 4.1.1. Projection Lens Focus (Rough) 4.1.2. Editing Channels, Sources, and VICs Figure 4.0-1 Channels Menu Figure 4.0-2 Sources Menu 4.1.3. Factory-Preset Channels and Sources Table 4.0-2 Channel 1 Factory Preset Sources 4.1.4. Internal Source 4.2. Timing Settings and Adjustments 4.2.1. Clamp Type 4.2.2. VTR Mode 4.2.3. Blanking 4.2.4. Phase 4.3. Geometric Adjustments 4.3.1. Centering (G) 4.3.2. Size FROM THIS TO THIS Figure 4.0-3 Phase, Size and Centering Adjustments Figure 4.0-4 Undistorted Standard Crosshatch Test Pattern 4.3.3. Bow Figure 4.0-5 Bow Distortion 4.3.4. Skew/Rotate (G) Figure 4.0-6 Vertical Rotation Distortion Figure 4.0-7 Skew Distortion-Vertical Centerline Tilted 4.3.5. Linearity (G) Figure 4.0-8 Linearity Distortion (horizontal and vertical) 4.3.6. Edge Linearity Figure 4.0-9 Edge Linearity Distortion (horizontal and vertical) 4.3.7. Keystone Figure 4.0-10 Keystone (horizontal and vertical) 4.3.8. Pincushion Figure 4.0-11 Pincushion Distortion (four views) 4.3.9. Centering (Red and Blue) 4.3.10. Linearity (Red and Blue) 4.3.11. Skew/Rotate (Red and Blue) 4.3.12. Projection Lens Focus (Fine) 4.4. CRT Focus and H/V Dynamic Focus 4.5. ILA Sensitivity and Bias Page 4.6. Convergence (XY Registration) 4.6.1. Purpose of Convergence 4.6.2. Cursor Shapes and Sizes Table 4.0-3 Cursor Modes 4.6.3. Convergence Profiled Figure 4.0-12 Full-Screen Cursor Center at Upper Left (Point 1) Figure 4.0-13 Screen Cursor Center at Upper Left (Point 1) Figure 4.0-14 Three (3) Cursor Modes Move Mode Size Mode Adjust Mode Page Figure 4.0-16 Incorrectly Converged RGB Patterns (two examples) 4.7. Black Level (G2) and Sensitivity Offset 4.7.1. Black Level (G2) Figure 4.0-17 Grey/Pluge Test Pattern 4.7.2. Sensitivity Offset 4.7.3. Threshold Offset 4.8. Uniformity (Shading) 4.8.1. Sensitivity Uniformity 4.8.2. Threshold Uniformity 4.8.3. Color Balance (Grey Scale) 4.9. Picture Settings Figure 4.0-18 Cont/Bright Test Pattern 4.9.1. Brightness 4.9.2. Contrast 4.9.3. Color, Tint, Sharpness 4.9.4. Black Enhance 4.9.5. VIC Settings 4.10. Backing up Settings 4.11. Video Input Cards Table 4.0-4 VIC Types 4.11.1. Installing (or Removing) a VIC Figure 4.0-19 Projector RGBHV Inputs with Optional Component HDTV (YPbPr) Input Module VIC Installed 4.11.2. Connecting VIC Source Cables Table 4.0-5 VIC Video Source Cable Connections 4.11.3. VIC Editing Table 4.0-6 VIC Edit Numbers Table 4.0-7 Optional VIC Port Numbers and LEDs 4.11.4. VIC Settings Table 4.0-8 Quad Decoder Modes Page Figure 4.0-23 Quad Standard Decoder Module (with Line Doubler) VIC 4.12. Updating Software Table 4.0-9 Terminal Preference Selections Table 4.0-10 Terminal Preference Selections Page Page Page Page 5.0 Preventive Maintenance 5.1. Preventive Maintenance 5.1.1. Cleaning the Cabinet 5.1.2. Cleaning the Projector Lens 5.1.3. Air Filters 6.0 System Specifications Page Page Page Appendix A. Extron Switcher Interface to Model 100 A.1 Extron Switcher Configuration A.2 Extron Users Manual Inaccuracies A.3 Key Operational Differences Between Models A.3.1 Switcher to Projector Configuration Example A.3.2 Failure Diagnostics Page Appendix BConfiguration Data Export / Import Procedures (Rev 1.0.0) Appendix B Note 1 Appendix B Note 2 Appendix B.1 EXPORT Appendix B.2 IMPORT Page Page Page 7.0 Glossary Of Terms Page Page Page Page Page Page Page 8.0 Indexes Index of Tables Index of Figures