JVC CA-HXZ77D, GVT0119-001C Creating Your Own Sound Mode-User Mode, Changing the Scanning Mode

English

Basic Operations (continued)

Creating Your Own Sound Mode—User Mode

You can change the SEA pattern to suit your preference. The SEA pattern can be adjusted using 3 frequency ranges—BASS,

MID (middle), and TRE (treble). These changed settings can be stored as the USER 1, USER 2, and USER 3 modes.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel ONLY:

1 Select one of the preset Sound modes. See “Selecting the Sound Modes” on page 16.

2 Press SET/DISPLAY while the selected Sound mode is still shown on the display.

Changing the Scanning Mode

This unit supports the NTSC progressive scanning system (480p*) as well as the conventional interlaced scanning system (480i*).

If your TV has component video jacks and supports progressive scanning system, you can enjoy a high quality picture from the built- in disc player.

•Refer also to the instruction manuals supplied with your TV.

•You can change the scanning mode only when “NTSC” is selected for the color system of this unit. See page 9.

•You cannot select the progressive scanning mode for the PAL system TVs.

Do not change the progressive scanning mode in the following cases:

–When your TV does not support the progressive video input.

–When you have not connected your TV to the unit using a component video cord.

On the remote control ONLY:

Current level appears.

3 Adjust the SEA pattern.

(1)Turn ¢ / 4 to select the frequency range (BASS, MID or TRE).

(2)Press ¡ / 1 to adjust the level of the selected frequency range.

•For adjusting BASS

Adjust the level within the range of ±0 to +3.

•For adjusting MID or TRE

Adjust the level within the range of –3 to +3.

(3)Repeat steps (1) and (2) to adjust the level of the other frequency ranges.

4 Press SET/DISPLAY again.

5 Turn ¢ / 4 to select one of the user modes (USER 1, USER 2, or USER 3) in which you want to store your SEA pattern.

6 Press SET/DISPLAY again.

The SEA pattern you have created is stored into the user mode selected in step 5.

To use your own sound mode

Select USER 1, USER 2, or USER 3 mode when using the Sound modes. See “Selecting the Sound Modes” on page 16.

Press PROGRESSIVE.

The PROGRESSIVE lamp lights up on the front panel.

•Each time you press the button, the scanning mode changes between “PROGRESSIV (progressive)” and “INTERLACE” alternately.

•Some progressive TVs and High-Definition TVs are not fully compatible with this system. When an incompatible picture is played back, turn off the progressive scanning mode. To check the compatibility of your TV, contact your dealer.

All JVC progressive TVs and High-Definition TVs are fully

compatible with this system.

*480p and 480i indicate the number of scanning lines and scanning format of an image signal.

–480p indicates 480 scanning lines with progressive format.

–480i indicates 480 scanning lines with interlaced format.

Prohibiting Disc Ejection—Tray Lock

You can prohibit disc ejection from the unit and lock disc trays.

• This operation is possible only when the unit is turned on.

On the front panel ONLY:

To prohibit disc ejection, press any one of 0 for disc trays while holding down 7. (If any disc tray is opened, close it first.) “LOCKED” appears for a while on the display, and all disc trays are locked.

To cancel the prohibition and unlock the disc tray, press any one of 0 for disc trays while holding down 7.

“UNLOCKED” appears for a while on the display, and all disc trays are released.

When you unplug the AC power cord or if a power
failure occurs	If you try to eject a disc while Tray Lock is in use

The setting will be erased in a few days. If this happens, set the user	“LOCKED” appears to inform you that the disc trays are locked.
modes again.

17