Adjusting the Voltage Selector
Before plugging in the unit, set the correct voltage for your area with the voltage selector on the rear of the unit.
|
|
|
|
| VIDEO OUT |
|
|
| |
|
|
| COMPONENT |
|
| VIDEO |
| ||
| P |
| P | Y |
|
|
|
|
|
|
|
|
|
|
|
|
| NTSC | PAL |
|
|
| ANTENNA |
|
|
|
|
|
|
AM EXT | AM |
|
|
|
|
|
| ||
|
| LOOP |
|
|
|
|
|
| |
|
|
| FM 75 |
|
|
|
|
| |
|
|
| COAXIAL |
|
|
|
|
| |
|
| RIGHT | LEFT |
| FRONT |
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| MAIN |
|
|
|
|
|
|
|
|
| SPEAKERS |
|
| |
|
|
|
|
|
| FRONT |
|
| |
|
|
|
|
|
| SUBWOOFERS |
| ||
CAUTION: SPEAKER IMPEDANCE | 6 | 16 |
|
|
| ||||
| AV |
|
|
|
|
|
| ||
COMPU LINK |
|
|
|
|
| VOLTAGE | |||
OPTICAL |
|
|
|
|
|
|
|
| SELECTOR |
DIGITAL |
|
|
|
|
|
|
|
|
|
OUTPUT |
|
|
|
|
|
|
|
|
|
AUX |
|
|
|
|
|
|
|
| Voltage mark |
IN |
|
| CENTER |
| RIGHT | LEFT |
|
| |
|
|
|
|
|
| ||||
RIGHT | LEFT |
|
|
|
|
|
|
| |
CENTER SPEAKER |
| SURROUND SPEAKERS |
| ||||||
|
| CAUTION: |
|
| CAUTION: |
|
| ||
SPEAKER IMPEDANCE | SPEAKER IMPEDANCE |
| |||||||
|
| 8 | 16 |
|
| 16 | 32 |
|
|
Use a screwdriver to rotate the voltage selector so that the voltage mark is pointing at the same voltage as where you are plugging in the unit. (See also the back cover page.)
DO NOT plug in before setting the voltage selector on the rear of the unit and all connection procedures are complete.
Now, you are ready to plug in the unit and any other connected equipment.
•If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.
IMPORTANT: Be sure to check that all connections are done before plugging the AC power cord into a wall outlet.
When connecting the AC power cord to a wall outlet, the unit automatically starts display demonstration.
To cancel the display demonstration, press and hold CANCEL/DEMO on the front panel until “DEMO OFF” appears on the display.
•When you press other buttons on the front panel or on the remote control, the demonstration stops temporarily. It will start automatically again (if no operation is done for about 2 minutes) unless you cancel it by pressing CANCEL/DEMO.
English
To cancel only beep sounds during the demonstration, press BEEP ON/OFF or press and hold BEEP (7) for more than 2 seconds on the front panel. The BEEP ON indicator goes off from the display.
On the remote control | On the front panel |
•“0:00” flashes on the display until you set the
To set the
To start the display demonstration manually, press and hold
CANCEL/DEMO again.
“DEMO START” appears on the display.
•Each time you press and hold the button, the display demonstration turns on and off alternately.
Setting the DVD Player
You need to set the following before starting playback, using the choice menu shown on the TV.
•You can select the language used in the choice menu.
•For further information about the choice menu, see pages 58 to 66.
Make sure you have selected the correct input mode on the TV before setting.
Step 1: Select the
Step 2: Select the monitor type according to your TV.
Is audio equipment connected to the OPTICAL DIGITAL OUTPUT
terminal?
YESNO
Step 3: Select the output signal type.
Setting is finished.
Go to the next page to start the initial setup.
If no operation is done for about 5 minutes while the choice menu is shown on the TV
The Screen Saver automatically works to prevent the TV screen from being damaged.
To cancel the Screen Saver, cancel this function. (See page 61.)
10