|
|
|
|
|
|
|
|
|
|
|
| E |
| N |
| 87 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| RECORDING |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| |||||||
|
| 5. | Audio dubbing is not possible. | ● The tape speed had been set to LP at | Set the tape speed to SP at the |
|
| |||||||||||
|
|
|
|
|
|
| the original recording. | original recording. |
|
| ||||||||
|
|
|
|
|
|
| ● HDD deck |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| This is normal. Audio dubbing is not |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| available for HDD deck. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
| 7. | When performing Tape Dubbing, | ● This is normal. |
|
|
|
|
|
|
|
|
| |||||
|
|
| the beginning of the dubbing start |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| point is not dubbed. |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
| TIMER RECORDING |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| |||||||
|
| 1. | Timer recording won’t work. | ● The clock and/or the timer have | Set the clock and/or timer correctly. |
|
| |||||||||||
|
|
|
|
|
|
| been set incorrectly. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ● The timer is not engaged. | Press TIMER and check to make sure |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| that ä appears on the front display |
|
| ||||||
|
|
|
|
|
|
|
|
|
| panel. |
|
| ||||||
|
|
|
|
|
|
| ● The recorder has not been set up |
|
| |||||||||
|
|
|
|
|
|
| properly. | Make sure you have compensated for |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| Guide Channel and recorder or cable |
|
| ||||||
|
|
|
|
|
|
|
|
|
| box channel number mismatches |
|
| ||||||
|
|
|
|
|
|
|
|
|
| (☞ pg. 56). |
|
| ||||||
|
|
|
|
|
|
|
| |||||||||||
|
| 2. | Timer programming won’t work. | ● Timer recording is in progress. | Timer programming can’t be performed |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| when timer recording is in progress. |
|
| ||||||
|
|
|
|
|
|
|
|
|
| Wait until it finishes. |
|
| ||||||
|
|
|
|
|
|
|
| |||||||||||
|
| 3. | ä and ] on the front display | ● The timer is engaged but there’s no | VHS deck |
|
| |||||||||||
|
|
| panel won’t stop blinking. | cassette loaded. | Load a cassette with the Record |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| Safety tab intact, or cover the hole |
|
| ||||||
|
|
|
|
|
|
|
|
|
| using adhesive tape. |
|
| ||||||
|
|
|
|
|
|
|
| |||||||||||
|
| 4. | The cassette is automatically | ● VHS deck | Remove the cassette and cover the |
|
| |||||||||||
|
|
| ejected, and ä and ] on the | The loaded cassette has had its | hole with adhesive tape, or insert a |
|
| |||||||||||
|
|
| front display panel won’t stop | Record Safety tab removed. | cassette with the Record Safety tab |
|
| |||||||||||
|
|
| blinking. |
|
|
| intact. |
|
| |||||||||
|
|
|
|
|
|
|
|
|
| Remove the cassette and set the erase |
|
| ||||||
|
|
|
|
|
|
|
|
|
| protection switch to “REC”. |
|
| ||||||
|
|
|
|
|
|
|
| |||||||||||
|
| 5. | ä blinks for 10 seconds and the | ● TIMER has been pressed when there | Check the programmed data and re- |
|
| |||||||||||
|
|
| timer mode is disengaged. | are no programs in memory, or the | program as necessary, then press |
|
| |||||||||||
|
|
|
|
|
|
| timer record program information | TIMER again. |
|
| ||||||||
|
|
|
|
|
|
| has not been programmed correctly. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||||||||||
|
| 6. | The cassette is automatically | ● The end of tape was reached during | The program may not have been |
|
| |||||||||||
|
|
| ejected, the power shuts off and ä | timer recording. | recorded in its entirety. Next time |
|
| |||||||||||
|
|
| and ] won’t stop blinking. |
|
|
| make sure you have enough time on |
|
| |||||||||
|
|
|
|
|
|
|
|
|
| the tape to record the entire program. |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CONTINUED ON NEXT PAGE
