JVC LPT0641-001A AV Insert Editing VHS deck only, Prepare the recording cassette, Start Editing

EN 63

A Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your VCR’s VIDEO or S-VIDEO and AUDIO input connectors.

B Set the VCR’s input mode.

Press AUX (number key “0”) and/or CH +/– to select “F-1” (or “L-1” if you use the connectors on the rear).

●When using S VIDEO connector, set “FRONT AUX INPUT” (or

“REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”. ( pg. 71, 73)

●When using VIDEO connector, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”. ( pg. 71, 73)

C Select the recording deck.

Press S-VHSor DV.

●When using the DV deck as the recording deck, press so that the video and audio signals from the VIDEO/S-VIDEO and AUDIO L + R input connectors can be recorded. The dubbing direction indicator ( S-VHS) lights.

D Prepare the recording cassette.

For the VHS deck

Load the recording cassette into the VHS deck, and play it back to determine the edit-out point (the end of the segment to be replaced) using the ADVANCED JOG dial, or pressing w e and PAUSE (9).

Then press C.RESET to reset the counter.

For the DV deck

Load the recording cassette into the DV deck.

E Locate the start point.

Determine the edit-in point (the beginning of the segment to be replaced) using the ADVANCED JOG dial, or pressing w e and PAUSE (9).

●Be sure to engage the Still mode at the edit-in point.

F Engage the Insert Editing mode.

Press INSERT.

●Your VCR enters the Insert Pause mode. (“o”, “u” and “i” light up on the front display panel.)

●The TV screen changes from the still picture to the input source you are going to record.

G Start Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press PLAY (4) to start the tape in your VCR; Insert Editing begins at this point.

●“o” and “u” are displayed on the front display panel.

H End Insert Editing.

For the VHS deck

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press C.RESET.

For the DV deck

Press STOP (8) to stop recording on the DV deck.

AV Insert Editing (VHS deck only)

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ...

... In step 6, after you press INSERT, press A.DUB also.

(“o” and “u” blink and “i” lights up on the front display panel.)

NOTES:

●Once the Insert Editing starts, you can not use the other deck.

●All necessary cables can be obtained from your dealer.

●Insert Editing cannot be performed on a VHS (or S-VHS) cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to “SAVE”.

●When Insert Editing is performed on a tape that has been recorded on another VCR, the inserted portion may appear distorted.

●In Insert Editing, the recording speed (SP/EP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point. (VHS deck only)

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel connectors.

When using these connectors, be sure to set “REAR AUX INPUT” to the appropriate mode. ( pg. 71)

●Insert Editing is not possible using the DV IN/OUT connector.

●Insert Editing is not possible on a blank portion of the tape.