CAUTION:
Be sure to turn down the volume:
•Before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
•Before removing headphones, as high volume may output from the speakers.
Activating TV Direct
TV Direct enables you to use this unit as an AV selector while the unit is not turned on.
When TV Direct is activated, the pictures and sounds go from the video components such as DVD player to the TV through this unit. In this case, you can use the video components and the TV as if they were connected directly.
•This function takes effect only when the video components and TV are connected to this unit with SCART cables.
•This function takes effect for the following
•This unit can be automatically turned on or off, and/or select the source automatically when you set the Auto Function mode to “AUTO1” or “AUTO2.” For details, see “Setting the Auto Function Mode” on page 19.
To activate (or deactivate) TV Direct, follow the procedure below:
1 Press TV DIRECT. | TV DIRECT |
All the indications disappear, then the source indicator currently selected lights red.
2Turn on the video component and TV.
3Press one of the source selecting
STB, or VCR.
The indicator corresponding to the selected source lights red.
DVD | STB | VCR |
To cancel TV Direct and turn off the unit, press
STANDBY/ON 
(or AUDIO 
on the remote control). The unit is turned off and the STANDBY lamp lights up.
To cancel TV Direct and turn on the unit, press TV DIRECT on the unit (or AUDIO on the remote control).
The unit is turned on and the source indicator currently selected lights green.
Notes:
•When TV Direct is activated, you cannot enjoy any of the sound effects this unit produces, and cannot use the speakers connected to this unit.
•You can use
Basic adjustment of auto memory
This unit memorizes sound settings for each source:
•when you turn off the power,
•when you change the source, and
•when you change the analogue/digital input mode (see page 13).
When you change the source, the memorized settings for the newly selected source are automatically recalled.
The followings can be stored for each source:
•Analogue/digital input mode (see page 13)
•Input attenuator mode (see page 20)
•Balance (see page 20)
•Bass boost (see page 21)
•Tone adjustment (see page 21)
•Subwoofer output level (see page 22)
•Surround mode selection (see pages 33 – 37)
Note:
If the source is FM or AM, you can assign a different setting for
each band.
For recording
You can record sounds of any sources playing through the unit to the VCR or the cassette deck.
While recording, you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording.
Note:
Sound adjustments (see page 20) and Surround adjustments (see
pages 32 to 37) cannot affect the recording.
Signal and speaker indicators on the display
Signal indicators |
|
|
|
|
|
|
| Speaker indicators | |||||||||
L | C | R |
|
|
|
|
|
|
|
| L C | R | |||||
ANALOG | L |
| C |
| R | PL ΙΙ | |||||||||||
|
| LFE |
|
|
|
|
|
|
|
|
|
| |||||
|
| LPCM | SUBWFR LFE DSP HP | SUBWFR |
|
| |||||||||||
|
| DOLBY D | LS |
| S |
| RS | AUTO SR |
|
| |||||||
LS | S | RS | DTS |
|
| INPUT ATT |
| LS |
|
| RS |
| |||||
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
| ||||||||||
The following signal indicators light up
L: • When digital input is selected: Lights up when the left channel signal comes in.
•When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the right channel signal comes in.
•When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in. LS : Lights up when the left rear channel signal comes in. RS : Lights up when the right rear channel signal comes in.
S : Lights up when the monaural rear channel signal or Dolby Surround encoded signal comes in.
LFE: Lights up when the LFE channel signal comes in.
The speaker indicators light up as follows:
•The subwoofer speaker indicator ( SUBWFR ) lights up when “SUBWFR” is set to “YES” (see page 15).
•The other speaker indicators light up only when the corresponding speaker is activated, and also when required for the current playback.
Basic Operations
11
