![](/images/new-backgrounds/1022474/2247437x1.webp)
“YES” for the subwoofer and “SML” for the front, center and rear speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions.
Setting the Subwoofer Information | Remote |
NOT |
Register whether you have connected a subwoofer or not. If you have already connected a subwoofer, follow the procedure below.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
| settings. |
1Press SETTING.
SETTING | The CONTROL buttons now work for basic |
settings.
2Press CONTROL ∞ (or 5) repeatedly until one of the following speakers (with the current
setting)* appears.
CONTROL |
|
|
| ||
ANALOG | L | C | R | PR ΙΙ |
|
LPCM | SUBWFR LFE DSP |
| |||
DOLBY D | LS | S | RS | AUTO SR | VOL |
DTS | INPUT ATT |
Basic Settings
2Press CONTROL ∞ (or 5) repeatedly until “SUBWFR (Subwoofer)” (with the current
setting)* appears on the display.
CONTROL
RΙΙ
SR |
|
ATT | VOL |
FRNT SP (Front Speaker) : To register the front speaker size.
CNTR SP (Center Speaker): To register the center speaker size.
REAR SP (Rear Speaker) : To register the rear speaker size.
*“SML (small)” is the initial setting. If you have already changed the setting, another size will be shown.
* “YES” is the initial setting. If you have already changed the | 3 Press CONTROL 3 (or 2) to select the | |
setting, “NO” will be shown. | ||
appropriate speaker size. | ||
3 Press CONTROL 3 (or 2) to select “YES.” | ||
• Each time you press the button, the speaker size changes as | ||
follows: | ||
• Each time you press the button, the subwoofer setting | ||
| ||
alternates between “YES” and “NO.” | CONTROL | |
CONTROL |
|
ANALOG | L | C | R | PR ΙΙ |
| ANALOG | L | C | R | PR ΙΙ |
|
| LPCM | SUBWFR LFE DSP |
| ||||||||
LPCM | SUBWFR LFE DSP |
|
| ||||||||
| DOLBY D | LS | S | RS | AUTO SR |
| |||||
DOLBY D | LS | S | RS | AUTO SR | VOL | DTS | INPUT ATT | VOL | |||
DTS | INPUT ATT |
|
|
| |||||||
|
|
|
|
|
|
YES : Select this when you have connected a subwoofer. The subwoofer speaker indicator ( SUBWFR ) lights up on the display (see page 11). You can adjust the subwoofer output level (see page 22).
NO : Select this when you have not connected or have disconnected a subwoofer.
Setting the Speakers | Remote |
Information | NOT |
To obtain the best possible effect from the Surround modes (see page 32), register the following information after all connections are completed.
•Speaker
•Speaker
•Crossover
•Low Frequency Effect
•Dynamic Range
Speaker Size—FRNT SP, CNTR SP, REAR SP
Register the sizes of all the connected speakers.
•When you change your speakers, register the information about the speakers again.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
Ex.: When registering the rear speaker size.
LRG (Large) | : Select this when the speaker size is relatively |
| large. (See “Notes” below.) |
|
|
SML (Small) | : Select this when the speaker size is relatively |
| small. (See “Notes” below.) |
|
|
NO | : Select this when you have not connected a |
| speaker. (Not selectable for the front speakers.) |
|
|
4Repeat steps 2 and 3 to select the appropriate size for the other speakers.
Notes:
•Use the following criteria as reference when adjusting:
–If the size of the cone speaker unit built in your speaker is greater than 12 cm, select “LRG (large),” and if it is smaller than 12 cm, select “SML (small).”
•If you have selected “NO” for the subwoofer, you can only select “LRG (large)” for the front speaker size.
•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for the center and rear speaker sizes.
15