Manuals / JVC / Home Audio / Home Theater System

JVC LVT0858-001A Getting Started, Connecting the FM and AM MW/LW Antennas, FM Antenna supplied

Models: LVT0858-001A

1 51

Download 51 pages 42.48 Kb

Page 8

Image 8

Getting Started

Connecting the FM and AM (MW/LW) Antennas

AM (MW/LW) Loop

Antenna (supplied)

Snap the tabs on the loop into the slots of the base to assemble the AM (MW/LW) loop antenna.

If AM (MW/LW) reception is poor, connect an outdoor single vinyl-covered wire (not supplied).

If FM reception is poor, connect outdoor FM antenna (not supplied).

FMCOAXIAL

AM LOOP

FM Antenna (supplied)

AM		FM 75
EXT		COAXIAL
	ANTENNA

AM	LOOP		75
			FM
			COAXIAL
		ANTENNA
AM	AUDIO
EXT
		IN
	OUT	(PLAY)
	OUT
	(REC)
	TAPE

		2
		DIGITAL
		(STB)
		TV
AV	IN/OUT
AV		SUBWOOFEROUT
		SUBWOOFEROUT
VCR
		STB
	AV	IN
	AV
DVD

DIGITAL

CENTER SPEAKER

+ –

IN	1
DIGITAL
(DVD)
	SPEAKERS
REAR	LEFT
RIGHT	+
	–

	SPEAKERS
	LEFT
FRONT	+
RIGHT	+

+ –

–

: CAUTION SPEAKER IMPEDANCE 16 8

Page 8

Image 8

JVC LVT0858-001A manual Getting Started, Connecting the FM and AM MW/LW Antennas, FM Antenna supplied

Contents

RX-E111RSL / RX-E112RSL If in Doubt Consult a Competent Electrician RX-E111RSL RX-E112RSL Above ALL Table of Contents Remote Control Parts Identification7 8 9 p Front PanelGetting Started Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Connecting the FM and AM MW/LW Antennas Getting StartedFM Antenna supplied AntennaConnecting the Speakers Connecting the front, center, and rear speakersConnecting the subwoofer speaker AM MW/LW antenna connectionSpeaker Layout Diagram RX-E111R RX-E112RConnecting Audio/Video Components Digital connectionsAnalogue ConnectionsVCR STB DVD Audio VideoVideo RGB Audio OUTConnecting the Power Cord Turn On the Power Adjust the VolumeBasic Operations Select the Source to PlayBasic adjustment of auto memory Signal and speaker indicators on the displayActivating TV Direct Press TV DirectBasic Operations Turning Off the SoundsTemporarily-Muting Changing the Display BrightnessBasic Settings Setting the Digital InputSelecting the Analogue or Digital Input Mode Digital in TerminalsBasic Settings Setting Input ANALOG/DIGITALControl ∞/ 3/ 2 DisplaySetting the Speakers InformationCurrent setting* appears on the display Press Control ∞ or 5 repeatedly untilPress Control 3 or 2 to select the distance Speaker Distance-FRNT D, Cntr D, Rear DPress Control 3 or 2 to select the LFE attenuator level Crossover Frequency-CROSSLow Frequency Effect Attenuator-LFE Dynamic Range Compression-D.COMPPress Control 3 or 2 to select on or OFF∞ /3 /2 DisplaySetting the Auto Function Mode To cancel Auto SurroundPress Control 3 or 2 to select AUTO1 or AUTO2 Repeat steps 1 and 2, then select OFF in stepSound Adjustments Press Control 3 or 2 to adjust the front speaker balanceAdjusting the Front Speakers Press AdjustAdjusting the Tone Reinforcing the BassSound Adjustments Adjusting the Subwoofer Output LevelPress Control 3 or 2 to adjust the sound Output level AdjustmentsTuning into Stations Manually Ex. When selecting the FM bandTuner Operations Press FM/AM to select the bandUsing Preset Tuning To erase a stored preset stationTuner Operations Press MemorySelecting the FM Reception Mode To tune in a preset stationTo restore the stereo effect Channel number you wantUsing the RDS Radio Data What information can RDS signals provide?System to Receive FM StationsSet RDS/DVD Menu selector to RDS. RDS Press PTY Search while listening To an FM stationPress PTY 9 or PTY until PTY code you want appears On the display, while PTY Select is flashingDescription of the PTY codes Jazz musicSwitching to Broadcast ProgramYour Choice Temporarily Press TA/NEWS/INFO repeatedlyCreating Realistic Sound Fields Dolby SurroundDTS Digital Surround Typical Multichannel 5.1-channel reproductionDAP Digital Acoustic Processor modes All Channel Stereo All Channel Stereo reproductionCreating sound field HallCreating Realistic Sound Fields About Relations between Speaker Layout and Surround ModesTurning on or off the Surround modes Selecting the Surround modesSurround mode Except for the digital multichannelPL II Music according to a playing source Press Test to check the speaker output balanceAdjust the following speaker output levels from -10 to +10 To cancel Surround ModePress Test again to stop the test tone Press SoundUsing DAP Modes and All Channel Stereo Remote Control Adjust the rear speaker output levels from -10 to +10To cancel DAP Modes and All Channel Stereo Only for ALL CH ST. to adjust the center speaker levelON/OFF Mode Panorama controlPress Control 3 or 2 to make adjustments Repeat steps 5 and 6 to adjust the other settingsUsing DAP Modes and All Channel Stereo Front Panel Repeat steps 5 and 6 to make other adjustmentsTurning on the power-POWER buttons Adjusting the volume-VOLUME buttonsMastering Remote Operations Reinforcing the Bass-BASS Boost buttonSelecting the channels-10 keys Adjusting the sound and operating tuner -10 keysOperating RDS These buttons work only for TV operations Mastering Remote OperationsOperating DVD menu for JVC’s DVD player Try to operate your DVD player by pressing Manufacturers’ codes for DVD player CodesTry to operate your STB by pressing STB Manufacturers’ codes for STB CodesIf there are more than one code listed for your brand of TV Manufacturers’ codes for VCR CodesCGM Try to operate your TV by pressing TVTroubleshooting Problem Possible Cause SolutionOperations To be on the NextTroubleshooting Specifications AmplifierSpecifications Tuning Range KHz toFM tuner IHF AM MW/LW tuner0102NHMMDWJEIN

Getting Started

Connecting the FM and AM (MW/LW) Antennas

FM Antenna (supplied)

ANTENNA