Tuner operations
3Press the numeric buttons (1 – 10, +10) to select a channel number while the channel number position is flashing.
•For channel number 5, press 5.
•For channel number 15, press +10, then 5.
•For channel number 30, press +10, +10, then 10.
ANALOG L | R | TUNED ST AUTO MUTING |
SUBWFR |
| MHZ |
|
| VOL |
4Press MEMORY again while the selected channel number is flashing on the display.
The station is assigned to the selected channel number.
• The selected channel number stops flashing.
ANALOG L | R | TUNED ST AUTO MUTING | ||
|
|
|
|
|
SUBWFR |
| MHZ | ||
|
|
|
| VOL |
|
|
|
|
|
5Press repeatedly or hold TUNING 9 or
TUNING ( to select another frequency you want to store.
6Repeat steps 1 to 5 until you store all the stations you want.
To erase a stored preset station
Storing a new station on a used channel number erases the previously stored one.
To tune in a preset station
From the remote control:
1Press FM/AM to select the band.
The last received station of the selected band is tuned in and the numeric buttons now work for tuner operations.
•Each time you press the button, the band alternates between FM and AM (MW).
ANALOG L | R | TUNED ST AUTO MUTING | ||
|
|
|
|
|
SUBWFR |
| MHZ | ||
|
|
|
| VOL |
|
|
|
|
|
2Press the numeric buttons (1 – 10, +10) to select a channel number.
If you select “FM” or “AM” using SOURCE SELECTOR on the front panel, press FM/AM on the remote control before this operation.
•For channel number 5, press 5.
•For channel number 15, press +10, then 5.
•For channel number 30, press +10, +10, then 10.
ANALOG L | R | TUNED ST AUTO MUTING | ||
|
|
|
|
|
SUBWFR |
| MHZ | ||
|
|
|
| VOL |
|
|
|
|
|
On the front panel:
|
|
|
|
|
|
|
|
|
|
| SOURCE SELECTOR | MASTER VOLUME |
| TV DIRECT | SETTING | ADJUST | SURROUND |
|
|
|
|
| SET / TUNER PRESET | / MULTI JOG |
|
|
|
|
|
|
|
|
|
|
|
|
| PHONES |
STANDBY / ON | STANDBY |
|
|
| DVD MULTI | DVD | STB | VR | TV | FM / AM |
|
|
Before you start, remember...
There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.
1 Turn SOURCE SELECTOR to select “FM” or “AM.”
The last received station of the selected band is tuned in.
2Press TUNER PRESET.
“P” appears on the display and MULTI JOG now works for selecting preset channels.
3Turn MULTI JOG to select a preset channel number during “P” appears on the display.
•Turning MULTI JOG clockwise increases the preset channel numbers.
•Turning MULTI JOG counterclockwise decreases the preset channel numbers.
ANALOG L | R | TUNED ST AUTO MUTING | ||
|
|
|
|
|
SUBWFR |
| MHZ | ||
|
|
|
| VOL |
|
|
|
|
|
Selecting the FM reception mode
When an FM stereo broadcast is hard to receive or noisy, you can change the FM reception mode while receiving an FM broadcast.
•You can store the FM reception mode for each preset station (see page 23).
From the remote control ONLY:
While listening to an FM station, press FM MODE.
If you select “FM” using SOURCE SELECTOR on the front panel, press FM/AM on the remote control before this operation.
•Each time you press the button, the FM reception mode alternates between “AUTO MUTING” and “MONO.”
AUTO MUTING*: | Normally select this. |
| When a program is broadcast in stereo, you |
| will hear stereo sound; when in monaural, you |
| will hear monaural sound. This mode is also |
| useful to suppress static noise between |
| stations. The AUTO MUTING indicator lights |
| up on the display. |
|
|
MONO: | Select this to improve the reception (but |
| stereo effect will be lost). |
| In this mode, you will hear noise while tuning |
| in to the stations. The AUTO MUTING |
| indicator goes off from the display. (The ST |
| indicator also goes off.) |
|
|
* Initial setting |
|
24