JVC LVT1112-001A manual Sound adjustments, Adjusting the tone-BASS,TREBLE, 1Press ADJUST

Sound adjustments

When operating the receiver using the remote control, always set the mode selector to AUDIO/TV/VCR/STB.

DVD

AUDIO/TV

/VCR/STB

Operating procedure

SOURCE SELECTOR

MASTER VOLUME

TV DIRECT

SETTING

ADJUST

SURROUND

SET / TUNER PRESET

/ MULTI JOG

PHONES

STANDBY / ON

STANDBY

DVD MULTI

DVD

STB

VR

TV

FM / AM

Adjusting the tone—BASS, TREBLE

You can adjust the bass and treble sounds to your preference.

• You have to make these adjustments for each source.

BASS*: To adjust the bass (from –10 dB to +10 dB).

TREBLE*: To adjust the treble (from –10 dB to +10 dB).

On the front panel:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press ADJUST.

MULTI JOG now works for the sound adjustment.

2Turn MULTI JOG until the setting item you want to set appears on the display, then press SET.

• As you turn MULTI JOG, the indication changes as follows:

*“0” is the initial setting.

When using the remote control:

1Press TONE.

2Press BASS 9/( or TREBLE 9/( to adjust the sound level (from –10 dB to +10 dB).

NOTE

AUDIO	SUBTITLE TITLE/GROUP RETURN
ZOOM		BASS	TREBLE
	1	2	3
		BASS	TREBLE
VFP	4	5	6
	7	8	9
ANGLE	TV RETURN		100+
	10	0	+10
REPEAT
	3D
DIMMER	SLEEP ANALOG/DIGITAL CANCEL
		INPUT
SMART S. SETUP	BASS BOOST		A.POSITION
		TONE
			SURROUND
TEST	EFFECT	DECODE
SUBWFR	CENTER	L	SURR R

ANALOG L R

SUBWFR

VOL

BASS	TREBLE		SUBWFR
CENTER	SURR L		SURR R
EFFECT	PANORAMA			BAL
B.BOOST	ATT	(Back to the beginning)

3Turn MULTI JOG to adjust the item selected in step 2, then press SET.

Your setting is stored.

ANALOG L R

SUBWFR

VOL

Ex.: When selecting “+10 (dB)” for “BASS”.

When you use the numeric buttons to operate your target source after tone adjustments, press the corresponding source selecting button first so that the numeric buttons work for your target source.

Adjusting the subwoofer output level

—SUBWFR

You can adjust the subwoofer output level if you have connected a subwoofer and set the subwoofer information correctly—“USE” for the Quick Setup or “YES” for the Manual Setup (see pages 16 and 17).

• You have to make this adjustment for each source.

SUBWFR*: To adjust the subwoofer output level (from –10 dB to +10 dB).

*“0” is the initial setting.

When using the remote control:

Press SUBWFR +/– to adjust the subwoofer output level (from –10 dB to +10 dB).

AUDIO	SUBTITLE TITLE/GROUP RETURN
ZOOM		BASS	TREBLE
	1	2	3
		BASS	TREBLE
VFP	4	5	6
	7	8	9
ANGLE	TV RETURN		100+
	10	0	+10
REPEAT
	3D
DIMMER	SLEEP ANALOG/DIGITAL CANCEL
		INPUT
SMART S. SETUP	BASS BOOST		A.POSITION
		TONE
			SURROUND
TEST	EFFECT	DECODE
SUBWFR	CENTER	L	SURR R

21