Creating Realistic Sound Fields
3 Press SOUND. | SOUND |
The 10 keys are activated for sound adjustments.
4 Press TEST to check if you can hear the | TEST |
| |
sounds through all the speakers at the | 1 |
| |
equal level. |
|
“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:
| TEST TONE L |
| TEST TONE C |
|
| TEST TONE R |
| ||||
| (Left front speaker) |
| (Center speaker) |
|
| (Right front speaker) | |||||
|
| TEST TONE LS |
| TEST TONE RS | |||||||
|
| (Left rear speaker) |
|
| (Right rear speaker) |
|
|
Notes:
•You can adjust the speaker output levels without outputting the test tone.
•No test tone comes out of the center speaker when “CNTR SP” is set to “NONE.”
•No test tone comes out of the rear speakers when “REAR SP” is set to “NONE.”
3Adjust the speaker output levels.
1) Press ADJUST repeatedly until one |
|
|
| ||
ADJUST | SETTING | ||||
|
| ||||
of the following indications (with the |
|
|
| ||
|
|
| |||
|
|
| |||
|
|
| |||
current setting)* appears on the |
|
|
| ||
display. |
|
|
| ||
|
|
|
| ||
| CENTER :To adjust the center speaker output level | ||||
|
|
|
| ||
|
|
|
|
|
REAR L : To adjust the left rear speaker output level
REAR R : To adjust the right rear speaker output level
*“0” is the initial setting. If you have already changed the setting, another number (level) will be shown.
2) Press CONTROL UP 5/ | DOWN UP |
| CONTROL |
DOWN ∞ to adjust the selected |
|
speaker output level. |
|
5Adjust the speaker output levels
Adjust the center speaker and rear speakers levels comparing to the sound from the front speakers.
• To adjust the center speaker level, press |
CENTER |
• To adjust the left rear speaker level, press |
REAR•L |
CENTER
2 3
REAR L
5 6
REARR
3)Repeat steps 1) and 2) to adjust the other speaker levels.
When you select “PL II MUSIC,” you can go to the following adjustment.
• To adjust the right rear speaker level, press |
REAR•R |
8 9
4 Turn on Panorama control or off. |
1) Press ADJUST repeatedly until |
Remote
NOT
6 Press TEST again to stop the test | TEST |
tone. | 1 |
|
On the front panel:
You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So make adjustments while listening to the sound of the source played back.
1Setting the analog or digital input mode for the
“PANORAMA” (with the current |
setting)* appears on the display.
*“OFF” is the initial setting. If you have already changed the setting, “ON” will be shown.
2)Press CONTROL UP 5/ DOWN ∞ to select if you turn on or off Panorama control.
•Each time you press the button, “ON” and “OFF” change alternately.
ADJUST SETTING
CONTROL
DOWN UP
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and DTS Digital Surround, select the digital input mode (see page 11).
2 Press SURROUND ON/OFF to | SURROUND ON/OFF |
| |
activate Surround mode. |
|
Each time you press the button, Surround mode turns on and off alternately.
•If you are playing back software encoded with Dolby Digital multichannel, “DOLBY DIGITAL” is selected.
•If you are playing back software encoded with DTS Digital Surround, “DTS SURROUND” is selected.
• If you are playing back any software other than above, you can select “PL II MUSIC” or “PL II MOVIE” according to the source by pressing SURROUND MODE. ( PRO LOGIC II indicator lights up on the display.)
If you like to adjust sound, go to step 3.
ON | : Select this when you like to enjoy |
| “wraparound” sound effect with |
| image. |
|
|
OFF | : Select this when you like to enjoy |
| originally recorded sounds. |
|
|
To cancel Surround mode
Press SURROUND ON/OFF again so that “SURROUND OFF” appears on the display.
•If Surround mode is canceled while playing back multichannel digital software, all channel signals are mixed and output through the front speakers (and subwoofer, if you have connected a subwoofer and set the subwoofer setting
22