Basic Operations
English
Turning Off the Sounds | Remote |
ONLY | |
Press MUTING on the remote control to mute | MUTING |
the sound through all speakers and headphones |
|
connected. |
|
•“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).
ANALOG SPK
L R
To restore the sound, press MUTING again.
•Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.
Turning Off the Power | Remote |
with the Sleep Timer | ONLY |
You can fall asleep while listening to
Press SLEEP on the remote control repeatedly. |
| SLEEP | |
• The SLEEP indicator lights up on the display, and the | |||
|
| ||
|
|
|
|
| ANALOG SPK | SLEEP |
|
| L R |
|
|
|
|
|
|
10 
20 
30 
40 
50 
60
0(Canceled) 
90 
80 
70 
When the
The receiver turns off automatically.
To check or change the time remaining until the
Press SLEEP once.
The remaining time (in minutes) until the
•To change the
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the display. (The SLEEP indicator goes off.)
•Turning off the power also cancels the Sleep Timer.
Basic adjustment auto memory
This receiver memorizes sound settings for each source when:
•you turn off the power,
•you change the source, and
•you assign the source name.
When you change the source, the memorized settings for the newly selected source are automatically recalled.
The following can be stored for each source:
•Input attenuator mode (see page 15)
•Balance (see page 15)
•Tone adjustment (see page 15)
•Subwoofer output level (see page 15)
•Surround mode selection (see pages 21 – 23 )
Notes:
•You cannot assign and store different settings for digital input mode and analog input mode.
•If the source is FM or AM, you can assign a different setting for each band.
For recording
You can record any sources playing through the receiver to a cassette deck (or a CD recorder) connected to the TAPE/CDR jacks and the VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording.
Note:
The output volume level, tone adjustment (see page 15), and
Surround modes (see page 18) cannot affect the recording.
Signal and speaker indicators on the display
Signal indicators |
|
|
| Speaker indicators | ||||||
L | C | R |
|
|
|
|
| L | C | R |
| ANALOG | SPK | ONETOUCH | |||||||
| DIGITAL AUTO | L C R | PROLOGIC ΙΙ | |||||||
|
|
|
| LINEAR PCM | S.WFR LFE |
|
|
|
|
|
S.WFR LFE |
| DIGITAL | LS S RS |
|
| S.WFR | LFE | |||
|
| CH- |
|
| ||||||
LS | S | RS |
|
|
|
|
| LS | S | RS |
|
|
|
|
| ||||||
The following signal indicators light
L: •When digital input is selected: Lights up when the left channel signal comes in.
•When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the right channel signal comes in.
•When analog input is selected: Always lights up.
C : When the center channel signal comes in.
LS : When the left rear channel signal comes in.
RS : When the right rear channel signal comes in.
S : When the monaural rear channel signal or 2 channel Dolby Surround encoded signal comes in.
LFE: When the LFE channel signal comes in.
The speaker indicators light up when both of the following conditions satisfied:
•The corresponding speaker is activated, and
•The corresponding speaker is required for the current playback.
Note:
When “SUBWOOFER” is set to “YES” (see page 12), S.WFR lights
up.
10
