Using DAP Modes and All Channel Stereo
Once you have adjusted the DAP modes and All Channel Stereo, the adjustment is memorized for each source.
•You cannot use the DAP modes and All Channel Stereo if the rear speakers are not connected or deactivated.
•You cannot adjust the effect level for “ALL CH STEREO.”
From the remote control:
It will be convenient for you to use the remote control for adjustments, since you can make adjustments from your listening point.
1Start playing 2 channel
2 Press SURROUND ON/OFF to | ON/OFF |
activate Surround mode. | SURROUND |
|
When Surround mode turns on, the last selected
Surround mode will be activated.
•Each time you press the button, Surround mode turns on and off alternately.
3Press SURROUND MODE repeatedly SURROUND
until one of the DAP | MODE |
| |
CLUB,” “DANCE CLUB,” “HALL,” |
|
| |
STEREO” appears on the display. |
|
2 Press SURROUND ON/OFF to | SURROUND ON/OFF |
| |
activate Surround mode. |
|
When the Surround mode turns on, the last selected Surround mode will be activated.
•Each time you press the button, Surround mode turns on and off alternately.
3 Press SURROUND MODE
repeatedly until one of the DAP
CLUB,” “HALL,” “PAVILION”—
or “ALL CH STEREO” appears on the display.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of the following indications (with the current setting)* appears on the display.
REAR L : To adjust the left rear speaker output level
REAR R : To adjust the right rear speaker output level
CENTER : For “ALL CH STEREO”
English
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4Press SOUND.
The 10 keys are activated for sound adjustments.
5Adjust the speakers output levels
•To adjust the left rear speaker level, press REAR•L
•To adjust the right rear speaker level, press REAR•R
For “ALL CH STEREO” only:
•To adjust the center speaker level, press CENTER
SOUND
REAR L
5 6
REARR
8 9
CENTER
2 3
center speaker output level
*“0” is the initial setting. If you have already changed the setting, another number (level) will be shown.
2) Press CONTROL UP 5/DOWN ∞ CONTROL
DOWN UP
to adjust the selected speaker output level.
3)Repeat steps 1) and 2) to adjust the other speaker level.
5For DAP modes only: Adjust the effect level.
1) Press ADJUST repeatedly until “EFFECT” (with the current setting)* appears on the display.
* “EFFECT 3” is the initial setting. If you have already |
6 For DAP modes only: |
|
Press EFFECT to select the effect | EFFECT |
level (1 to 5) you want. | 4 |
|
•Each time you press the button, the effect level changes as follows:
changed the setting, another setting will be shown. |
2) Press CONTROL UP 5/DOWN ∞ CONTROL
DOWN UP
to select the effect level (1 to 5) you want.
•Each time you press the button, the effect level changes as follows:
EFFECT 1 | EFFECT 2 | EFFECT 3 | EFFECT 1 | EFFECT 2 | EFFECT 3 |
EFFECT 5 | EFFECT 4 |
| EFFECT 5 |
|
| EFFECT 4 |
|
| |||||
As the number increases, selected mode becomes stronger | As the number increases, selected mode becomes stronger | |||||
(normally set it to “EFFECT 3”). |
| |||||
(normally set it to “EFFECT 3”). |
|
| ||||
| Note: |
|
| |||
|
|
| ||||
|
| You cannot select any DAP mode and All Channel Stereo when software | ||||
On the front panel: |
| encoded with Dolby Digital or DTS Digital Surround is played back. | ||||
|
|
|
|
|
| |
1 Start playing 2 channel | To cancel DAP modes and All Channel Stereo | |||||
or Linear | Press SURROUND ON/OFF so that “SURROUND OFF” appears | |||||
|
| on the display. The DSP indicator goes off. |
|
23