Connecting the rear and center speakers

Cut, twist and remove the insulation at the end of each speaker signal cable first, and then, connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals by using the cables.

	CENTER		REAR
	SPEAKER	SPEAKERS
		RIGHT	LEFT
Center speaker
Left rear speaker	Right rear speaker

1 Open the terminal and then

2 Close the terminal.

insert the speaker signal cable.

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer.

Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs.

SUBWOOFER

OUT

Powered subwoofer

English

Page 17

Image 17

JVC RX-774RBK manual Connecting the rear and center speakers, Connecting the subwoofer speaker

Contents

RX-774RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-774RBK Table of Contents Selecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the DSP Modes Front Panel Parts Identification3 4 5 6 78 9 0-= To use the Multi JOG control ª on the front panel When using the remote control Remote Control RX-774RBK Easy Set Up & Operations Turn on the power Select the source For Reproducing DVD Multi playback with your DVD player Easy Set Up & Operations Multi Phono General Getting StartedLocations Handling the receiver Using the Supplied FM Antenna Connecting the FM and AM MW/LW AntennasUsing the Standard Type Connector Not Supplied FM Antenna Connections Getting Started Connecting the front speakersConnecting the Speakers Connecting the subwoofer speaker Connecting the rear and center speakers About the speaker impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers Audio Components Video Components Connecting Audio/Video ComponentsAudio component connections TV connection as the monitor Video component connections DVD player connection When you connect the DVD player with stereo output jacks To audio output DBS tuner TV as the sound source or DBS tuner connection Input VCR connection To shut off the power completely Connecting the Power CordPress Power to set it in the Ñoff position Putting Batteries in the Remote Control Turning the Power On and Off Standby From the remote controlBasic Operations On the front panel To increase the volume, turn Master Volume Adjusting the VolumeBasic Operations Press one of the source selecting buttons directly On the front panel only From the remote control onlyListening only with headphones Adjusting the Front Speaker Output Balance Basic SettingsListening at Low Volume Loudness Changing the Source Name When the shut-off time comes Using the Sleep TimerTo cancel the Sleep Timer Setting Center and Rear Speakers for DSP Modes Rear Speaker Setting Basic SettingsSelect this mode when you use rear speakers Select this mode when you do not use rear speakers To recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch Operation Using Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio Broadcasts To tune in a preset station To erase a stored preset station Press FM Mode to select the FM reception mode Selecting the FM Reception ModePress FM MODE/MUTE to select the FM reception mode Receiving Radio Broadcasts Tune in a preset station. See page 28 for details Assigning Names to Preset StationsPress Tuner PRESET, while a character you want is flashing Character is flashing after you have assigned a name To show the RDS signals Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop To stop searching any time during the process Descriptions of the PTY codes Press PTY Search while listening to an FMStation Receiver enters EON standby mode Switching to a Broadcast Program of Your Choice TemporarilyTraffic Announcement in your area News To stop listening to the program selected by EON To cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustment On 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround mode Using the 3D-PHONIC Modes Using the DSP ModesPress DSP Mode Press BALANCE/SURROUND Adjust repeatedly Keys are activated for sound adjustments To cancel the 3D-PHONIC modePress Sound Control Press Effect to select the effect level No DSP mode is applied Using the DAP ModesGives the feeling of a live music club with a low ceiling Gives a throbbing bass beat To cancel the DAP mode Each time you press the button, the effect level changes Press Rearl +/- to adjust the rear speaker output level Press Test to start checking the speaker output balance No DSP mode is applied For the other modes, see pages 39Preparing for Surround Modes Adjusted level are also shown on the equalizer display If necessary, adjust the speaker output level as followsCenter tone adjustment affects the mid-frequency For Dolby Pro Logic Center tone cannot be Press Surround Mode repeatedly until OFF appears Using Surround ModesTo cancel the Surround mode Speaker Arrangements for DVD Multi Playback Using the DVD Multi Playback ModeActivating the DVD Multi Playback Refer to the manual supplied with the DVD player SOFT2 SOFT1 Flat SHARP1 SHARP2 Keys are activated for adjusting the sound Using the DVD Multi Playback ModePress Cntr +/- to adjust the center speaker output level Press DVD Multi so that DVD Multi appears on the display When you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and Sound Adjusting the Front Speaker Output Balance Also see Using the On-Screen MenusListening at Low Volume Loudness Also see Sound Control menu appears Selecting Your Favorite SEA Mode Also see Press SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeSetting the Center Speaker Size Also see Operating the Tuner Setting the Rear Speaker Also seeSetting the Delay Time Also see Assigning Names to the Preset Stations Also see Storing the Preset Stations Also seePreset Memory menu appears Character entry screen appears RDS Information menu appears Checking the RDS Information Also see Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized Recording Plugs not supplied with this receiver Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD Player Showing the Disc Information on the TV Screen Text Compu Link Remote Control System Search a disc by its performer Searching a Disc Only for the CD playerPress SET again Going back to the Performer Search screen Press Exit Search a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þto move to GENRE, then press Genre Search screen appears Going back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV For the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SET Enter the song title, referring to steps 3 and 4 on For the MD recorderEnter the title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Turntable CD player-changerPlay Starts playing Stop Stops playing Cassette deck Operating JVC’s Audio/Video Components VCRmode selector is set to the correct position Sets the input mode either TVFollowing buttons can be used for operating the TV Turns on and off TV 10, 0, 100++10 Operating Other Manufactures’ Components Pauses Starts playbackStarts recording or enters recording Pause Manufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Problem Possible Cause Solution Troubleshooting Amplifier Specifications Video EN, GE, FR, NL, SP, IT 0498OFMMDWJEM