Video | JVC RX-774RBK specs

English

Video

Video Input Sensitivity/Impedance	Composite video: TV SOUND/DBS, VCR, DVD	1 Vp-p/75 ohms
	S-video: DVD
	(Y: luminance):	1 Vp-p/75 ohms
	(C: chrominance, burst):	0.286 Vp-p/75 ohms
Video Output Level	Composite video: VCR, MONITOR OUT	1 Vp-p/75 ohms
	S-video: MONITOR OUT	1 Vp-p/75 ohms
	(Y: luminance):	1 Vp-p/75 ohms
	(C: chrominance, burst):	0.286 Vp-p/75 ohms
Synchronization		Negative
Signal-to-Noise Ratio		45 dB
On-Screen Color System		PAL

FM tuner (IHF)

Tuning Range		87.5 MHz to 108.0 MHz
Usable Sensitivity	Monaural	12.7 dBf (1.2 µV/75 ohms)
50 dB Quieting Sensitivity	Monaural	16.3 dBf (1.8 µV/75 ohms)
	Stereo	38.3 dBf (22.5 µV/75 ohms)
Signal-to-Noise Ratio (IHF-A weighted)	Monaural	80 dB at 85 dBf
	Stereo	73 dB at 85 dBf
Total Harmonic Distortion	Monaural	0.15 % at 1 kHz
	Stereo	0.2 % at 1 kHz
Stereo Separation at REC OUT		40 dB at 1 kHz
Capture Ratio		1.5 dB at 85 dBf
Alternate Channel Selectivity		60 dB: (±400 kHz)
Frequency Response		30 Hz to 15 kHz: (+0.5 dB, –3 dB)

AM (MW/LW) tuner


Tuning Range		522 kHz to		1,629 kHz (MW)
		144 kHz to		288 kHz (LW)
Usable Sensitivity	Loop antenna	300	µV/m (MW)
		600	µV/m (LW)
Signal-to-Noise Ratio		50 dB (100 mV/m)

General

Power Requirements	AC 230V	, 50 Hz
Power Consumption	280 watts
	2 watts (in standby mode)
Dimensions (W x H x D)	435 x 157 x 412.5 mm
	(17 3/16 x 6 3/16 x 16 1/4 inches)
Mass	11.3 kg (25.0 lbs)

Designs & specifications are subject to change without notice.

78

Image 83

JVC RX-774RBK manual Video

Contents

RX-774RBK Per I’ltalia English Deutsch Français Nederlands Español Italiano Voorzichtig -- Power en STANDBY/ON RX-774RBK Table of Contents Selecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the DSP Modes To use the Multi JOG control ª on the front panel Parts IdentificationFront Panel 3 4 5 6 78 9 0-= When using the remote control Remote Control RX-774RBK Easy Set Up & Operations Turn on the power Select the source For Reproducing DVD Multi playback with your DVD player Easy Set Up & Operations Multi Phono Handling the receiver Getting StartedGeneral Locations FM Antenna Connections Connecting the FM and AM MW/LW AntennasUsing the Supplied FM Antenna Using the Standard Type Connector Not Supplied Getting Started Connecting the front speakersConnecting the Speakers Connecting the subwoofer speaker Connecting the rear and center speakers About the speaker impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers Audio Components Video Components Connecting Audio/Video ComponentsAudio component connections TV connection as the monitor Video component connections DVD player connection When you connect the DVD player with stereo output jacks To audio output DBS tuner TV as the sound source or DBS tuner connection Input VCR connection Putting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Press Power to set it in the Ñoff position On the front panel From the remote controlTurning the Power On and Off Standby Basic Operations Press one of the source selecting buttons directly Adjusting the VolumeTo increase the volume, turn Master Volume Basic Operations On the front panel only From the remote control onlyListening only with headphones Changing the Source Name Basic SettingsAdjusting the Front Speaker Output Balance Listening at Low Volume Loudness Setting Center and Rear Speakers for DSP Modes Using the Sleep TimerWhen the shut-off time comes To cancel the Sleep Timer Select this mode when you do not use rear speakers Basic SettingsRear Speaker Setting Select this mode when you use rear speakers One Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation function Receiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning To store the preset stations To tune in a preset station To erase a stored preset station Receiving Radio Broadcasts Selecting the FM Reception ModePress FM Mode to select the FM reception mode Press FM MODE/MUTE to select the FM reception mode Character is flashing after you have assigned a name Assigning Names to Preset StationsTune in a preset station. See page 28 for details Press Tuner PRESET, while a character you want is flashing To show the RDS signals Using the RDS Radio Data System to Receive FM StationsWhat Information Can RDS Signals Provide? To stop searching any time during the process To search for a program using the PTY codesSearching for a Program by PTY Codes To continue searching after the first stop Descriptions of the PTY codes Press PTY Search while listening to an FMStation News Switching to a Broadcast Program of Your Choice TemporarilyReceiver enters EON standby mode Traffic Announcement in your area To stop listening to the program selected by EON To cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode To erase a stored adjustment Using the SEA ModesCreating Your Own SEA Mode To recall your own SEA adjustment On Surround mode Using the DSP ModesOn 3D-PHONIC mode On the DAP mode Press BALANCE/SURROUND Adjust repeatedly Using the DSP ModesUsing the 3D-PHONIC Modes Press DSP Mode Press Effect to select the effect level To cancel the 3D-PHONIC modeKeys are activated for sound adjustments Press Sound Control Gives a throbbing bass beat Using the DAP ModesNo DSP mode is applied Gives the feeling of a live music club with a low ceiling To cancel the DAP mode Each time you press the button, the effect level changes Press Rearl +/- to adjust the rear speaker output level Press Test to start checking the speaker output balance No DSP mode is applied For the other modes, see pages 39Preparing for Surround Modes Adjusted level are also shown on the equalizer display If necessary, adjust the speaker output level as followsCenter tone adjustment affects the mid-frequency For Dolby Pro Logic Center tone cannot be Press Surround Mode repeatedly until OFF appears Using Surround ModesTo cancel the Surround mode Refer to the manual supplied with the DVD player Using the DVD Multi Playback ModeSpeaker Arrangements for DVD Multi Playback Activating the DVD Multi Playback SOFT2 SOFT1 Flat SHARP1 SHARP2 Press DVD Multi so that DVD Multi appears on the display Using the DVD Multi Playback ModeKeys are activated for adjusting the sound Press Cntr +/- to adjust the center speaker output level Selecting the Different Sources for Picture and Sound Using the On-Screen MenusWhen you select OSD, see Selecting the Source to Play Also see Sound Control menu appears Using the On-Screen MenusAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also see Selecting Your Favorite SEA Mode Also see Press SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeSetting the Center Speaker Size Also see Operating the Tuner Setting the Rear Speaker Also seeSetting the Delay Time Also see Character entry screen appears Storing the Preset Stations Also seeAssigning Names to the Preset Stations Also see Preset Memory menu appears RDS Information menu appears Checking the RDS Information Also see Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source Selection Disc Search Only for CD Player Text Compu Link Remote Control SystemPlugs not supplied with this receiver Displaying the Disc Information on the TV screen Showing the Disc Information on the TV Screen Text Compu Link Remote Control System Going back to the Performer Search screen Press Exit Searching a Disc Only for the CD playerSearch a disc by its performer Press SET again Genre Search screen appears Going back to the Disc Title Search screen Press ExitSearch a disc by its genre Press on Screen Control %/ Þto move to GENRE, then press Going back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV To move to Shift , then press SET Entering the Disc InformationFor the CD Player with the disc memory function Title Input Performer screen appears on the TV Enter the song title, referring to steps 3 and 4 on For the MD recorderEnter the title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Cassette deck CD player-changerTurntable Play Starts playing Stop Stops playing Operating JVC’s Audio/Video Components Turns on and off TV Sets the input mode either TVVCRmode selector is set to the correct position Following buttons can be used for operating the TV 10, 0, 100++10 Operating Other Manufactures’ Components Pause Starts playbackPauses Starts recording or enters recording Manufacturers’ codes for TV Manufacturers’ codes for Catv converters Manufacturers’ codes for VCR Problem Possible Cause Solution Troubleshooting Amplifier Specifications Video EN, GE, FR, NL, SP, IT 0498OFMMDWJEM