JVC RX-774RBK manual Operating JVC’s Audio/Video Components

English

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 59) in addition to the connections using cables with RCA pin plugs (see page 14).

•Aim the remote control directly at the remote sensor on the receiver.

Notes:

• If you use the buttons on the

front panel or the menu

function to choose a source,

the remote control will not

operate that source. To

operate a source with the

Tuner

After pressing FM/AM (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations:

FM/AM:Alternates between FM and AM (MW/ LW).

1 – 10, +10: Selects a preset channel number directly. For channel number 5, press 5. For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

PTY SEARCH: Searches for a program by PTY codes.

PTY +/–:Selects the PTY codes.

DISPLAY MODE: Shows the RDS signals.

FM MODE/MUTE: Changes the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”) :

SEA MODE:Changes the SEA modes.

SURROUND MODE: Changes the DSP modes.

RM-SR774RU REMOTE CONTROL

TV/CATV		VCR	SLEEP		AUDIO
/DBS
DVD MULTI		DVD	VCR		TV/DBS
CD		TAPE/MD PHONO			FM/AM
SEA		CNTR TONE		CNTR MENU
MODE		1		2	3
SURROUND TEST ENTER				REAR (L)
MODE		4		5	6
SOUND
		EFFECT		(REAR R)
CONTROL		7/P		8	9
CD
		DELAY
DISC		10		0	+10
		RETURN FM MODE/MUTE			100+
AUDIO/TV
/VCR
		VOLUME
CATV
/DBS
		CHANNEL
MUTE					+
				PTY
		PTYSEARCH		FF / ¢
PTY	–	PLAY
/REW
4
				PAUSE
		STOP
REC
		MODE
		DISPLAY	TV VOLUME
TV/VIDEO
		CONTROL
		VCR	TAPE

SETEXIT

	remote control, the source
	must be selected using
	buttons on the remote control.
•	Check to see if its remote
	control mode selector is set to
	the correct position. To
	operate audio system, TVs,
	and VCRs, set it to “AUDIO/
	TV/VCR.”
•	Refer also to the manuals
	supplied with your
	components.

Note:

After adjusting sounds, press

O							L
N	S		M ENU		T		O
		C		N		R
After pressing SOUND CONTROL (with the remote control			REEN CO

mode selector set to “AUDIO/TV/VCR”) , you can perform the following operations:

CNTR +/–:Adjusts the center speaker output level for the Surround/DVD MULTI playback modes.

REAR•(L) +/–:Adjusts the left/right rear speaker output level for the DSP modes.

Adjusts the left rear speaker output level for the DVD MULTI playback mode.

(REAR•R) +/–:Adjusts the right rear speaker output level for the DVD MULTI playback mode.

DELAY:Selects the delay time of the rear speaker sound.

EFFECT:Selects the effect level for the DSP modes.

TEST:Turns on or off the test tone output for the Surround mode.

CNTR TONE: Selects the center tone level for the Surround/DVD MULTI playback modes.

CD player

After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations on a CD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous) track.
¢:	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.

1 – 10, +10: Selects a track number directly.

For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.

the corresponding source selecting button or CD DISC to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for operating your target source.

67