JVC TH-A5 manual Adjusting DSP Modes

5To adjust the output level for the center speaker, the rear speakers, and the subwoofer

1) Press SOUND repeatedly to select the SOUND

“CEN,” “REAR,” or “SW.”

•Each time you press the button, the indication on the display changes as follows:

00 F 00 00 R 00 CEN

	Normal indication		SW	REAR
	(canceled)
CEN (Center)		: To adjust the output level for center
		speaker (from –06 dB to +06 dB).
REAR		: To adjust the output level for rear
		speakers (from –06 dB to +06 dB).

SW (Subwoofer) : To adjust the output level for subwoofer (from –06 dB to +06 dB).

• When selecting “3 STEREO,” you cannot adjust the output

levels for the rear speakers and subwoofer.

• “CEN –06dB,” “REAR –06dB,” and “SW –06dB” are the

initial settings. If you have already changed the settings,

another value will appear.

1Select and play any source except Dolby Digital or DTS Digital Surround.

2 Press DSP MODE (or DSP on the front DSP MODE panel) repeatedly to select the desired DSP mode.

The DSP indicator lights up on the display while the DSP modes are activated.

•Each time you press the button, DSP mode changes as follows:

HALL THEATER PAVILION

Normal

indication LIVE CLUB DANCE CLUB (canceled)

Now, you are ready to start the adjustment.

•To adjust the output balance for the front speakers and the rear speakers, go to the next step.

•To adjust the output level for the rear speakers, go to step 4 on the next page.

•To adjust the overall level of DSP effect, go to step 5 on the next page.

3To adjust the output balance for the front speakers and the rear speakers

English

2) Press 3 or 2 to adjust the output level.

1) Press SOUND repeatedly until one of the following adjustment indications appears on the display.

SOUND

3: Increases the output level.

2 : Decreases the output level. ENTER

3) Repeat 1) and 2) for setting the other speakers.

Adjusting DSP Modes

You can adjust the following settings while activating DSP modes. It is recommended that you make adjustments from your actual listening point while listening to reproduced sounds.

–Output balance for the front speakers

–Output balance for the rear speakers

–Output level for the rear speakers

–Output level for the subwoofer

–Overall level of DSP effect

•DSP modes cannot be used with Dolby Surround. Once one of DSP modes is activated, Dolby Surround in use will be canceled.

•When you play back a DVD encoded with Dolby Digital or DTS Digital Surround, DSP MODE button (or DSP button on the center unit) does not work.

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 16). You cannot adjust the speaker output balance and levels when you have set the speaker settings to “NONE.”

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

•Each time you press the button, the indication on the display changes as follows:

		00 F 00		00 R 00		REAR
	Normal		REVERB		LIVE	ROOM
	indication
(canceled)

00 F (Front) 00 : To adjust the output balance for the front speakers.

00 R (Rear) 00 : To adjust the output balance for the rear speakers.

•“00 F 00” and “00 R 00” are the initial setting (the output balances are at the center position). If you have already changed the setting, another value will appear.

2) Press 3 or 2 to adjust the output balance.

3 : Decreases the left speaker

ENTER

output, or restores the right speaker output.

2 : Decreases the right speaker output, or restores the left speaker output.

•Each output balance changes from

OFF (silence), –06 (most reduction) to 00 (no reduction).

3)Repeat 1) and 2) for setting the other speaker.

TO BE CONTINUED ON THE NEXT PAGE

23