Table of Contents | JVC TK-C215VP4U/E, TK-C215VP12U/E instruction

Introduction

Table of Contents
Introduction
Safety Precautions	3
Characteristics	5
Table of Contents	6
Precautions for proper use of this product ...	7
Name of Parts	9
Setting the Switches and the Lens
(TK-C215VP4U/E)	12
Setting the Switches and the Lens
(TK-C215VP12U/E)	14

Before starting an important recording, be sure to perform a test recording in order to confirm that a normal recording is possible.

We will not provide any compensation whatsoever for the contents to be recorded or loss of opportunities when recording is not properly performed due to malfunction of the video camera, VTR, hard disk recorder or video tape.

Before touching the camera unit, make sure to touch the metal surface of the [MONITOR] terminal to discharge any static electricity from your body. Static electricity may cause the camera to malfunction.

Installation and Connection
System Example	16
About Connection Cables	17
Video signal cables	17
DC 12 V or AC 24 V
power supply cable	17
Electrical Specifications of
Alarm Input Terminals	18
The right sequence to connect and set the
camera	19
Setting the switches	20
Mounting the base	21
Cable Connection	22
Mounting the camera unit	23
Adjusting the video image	25
Mounting the inner dome	30
Mounting the dome cover	30
Mounting the camera using
the electrical box	31
Mounting the camera using the pipe	32
White-spot correction	34
Others
Specifications	36

6

Image 6

JVC TK-C215VP4U/E, TK-C215VP12U/E manual Table of Contents

Contents

TK-C215VP4U/E Instructions TK-C215VP12U/E For Customer Use Introduction Safety Precautions For USA and Canada Dear Customer Characteristics Table of Contents Precautions for proper use of this product Storage and Location of UseOthers Note on consumable parts MaintenanceEnergy Conservation TK-C215VP12U/E only Name of Parts Camera Video signal output connector BNC AC 24 V/DC 12 V Power Supply WireAlarm signal cable TK-C215VP12U/E only Base Camera Interior Memo B,+/- R/B,+/- adjustment button Setting the Switches Lens TK-C215VP4U/ERESET/SPOT RESET/SPOT button Function selection switches AGC Auto-gain control switch BLC Backlight compensation switch Sync Synchronization system selection switchWHT.BAL. ATW/MANUAL selection switch DAY/NIGHT Easy Day & Night switch Alarm Position status indication LED B,+/- R/B, +/- adjustment buttonPosition Select Position Select button Alarm alarm input mode selection switch Trigger System Example Metal Contact Video signal cables DC 12 V or AC 24 V power supply cableAbout Connection Cables Electrical Specifications of Alarm Input Terminals ‹ Polarity of alarm signals Right sequence to connect and set the camera Removing the dome cover Setting the switchesSetting the switches Removing the inner dome Mounting the base SetupMounting the fall prevention wire to a firm place Removing the camera unit from the base Connect the alarm cable. TK-C215VP12U/E onlyA Pg Connecting the coaxial cable a PgConnecting the AC 24 V/DC 12 V power supply wires Cable Connection Mounting the camera unit to the base Mounting the camera unitFill the hole with sealing material Fastening the 2 fastening screws of the camera unit Inserting the silica gel supplied Adjusting the video image Adjusting the shooting direction of the cameraMounting the test monitor Adjusting the focus Adjusting the angle of view, focus and brightnessAdjusting the angle of view TK-C215VP4U/E Adjusting the brightness TK-C215VP12U/E Adjust the focusAdjust the brightness Registering home position Registering alarm position Mounting the inner dome Mounting the dome cover Mounting the camera using the electrical box Following procedures are same as normal mounting Mounting the base to the pipe Mounting the camera using the pipeMounting the fall prevention wire to a firm place a Pg Fastening the base to the ceiling Removing the plug for the piping hole of the base White-spot correction Page Specifications Camera Lens General Dimensional Outline Drawing Focus chart TK-C215VP4U/E TK-C215VP12U/E Dome Camera