JVC XV-NA7SL manual Initial setup before using the unit, Use 5/∞ to select a desired language

Basic operations

operations

Initial setup before using the unit

We recommend you to set the display language, TV monitor type, analog audio output and digital output before using the unit, by following the procedure below.

When turning on the unit for the first time, the DVD PLAYER SET UP display automatically appears. In such a case, perform the following procedure from step 2.

See "Changing the initial settings" beginning on page 57 for details about each setting item.

	TV	DVD
OPEN/	STANDBY/ON
CLOSE	TV	DVD

	TV1	TV2	TV3
	1	2	3
	TV4	TV5	TV6
	4	5	6
	TV7	TV8	TV9
	7	8	9
	TV-/--	TV0	MUTING
ENTER	10	0	+10
		TITLE/	TV/VIDEO
	RETURN	PAGE GROUP	CANCEL

U			M
EN	CH
M			EN
P	+		U
TO				5/∞
VOL-			VOL+
		ENTER

CHOICE	HOICE	-		SCREE
	C	CH		N
				ON
	PREVIOUS			NEXT
	CLEAR	SELECT		STROBE
	SLOW-			SLOW+
	REPEAT SUB TITLE		AUDIO	VFP
			fs/Rate	PROGRESSIVE
	DIGEST	ANGLE		SCAN
			ZOOM
	3D	PAL/	AMP VOL
	PHONIC	NTSC

RM-SXV012E

REMOTE CONTROL

Basic

1 Press CHOICE for a few seconds to bring up the first page of the DVD PLAYER SET UP display.

The pull-down menu of the [ON SCREEN LANGUAGE] is already open.

DVD PLAYER SET UP
MENU LANGUAGE		ENGLISH
AUDIO LANGUAGE		ENGLISH
SUBTITLE		ENGLISH
ON SCREEN LANGUAGE		ENGLISH
		ENGLISH
		FRENCH
		GERMAN
SELECT	USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER

ON SCREEN LANGUAGE options

2 Use 5/∞ to select a desired language.

You can select the on-screen language for the preference displays, etc. from among English, French and German.

3 Press ENTER.

The second page is shown, in which the pull-down menu of the [MONITOR TYPE] is already open.

DVD PLAYER SET UP
MONITOR TYPE	4:3 L.B.
STILL MODE	16:9 NORMAL
	AUTO
	16:9 AUTO
SCREEN SAVER	4:3 LB
MP3/JPEG	4:3 PS
SELECT	USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER

MONITOR TYPE options

4 Use 5/∞ to select a desired monitor type.

You can select the monitor type according to your TV.

•For a normal (conventional) TV, select [4:3 LB] or [4:3 PS].

•For a wide-screen TV, select [16:9 AUTO] or [16:9 NORMAL].

See page 59 for details about each mode.

5 Press ENTER.

The third (final) page is shown, in which the pull- down menu of the [ANALOG OUT] is already open.

DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT		STREAM/PCM
ANALOG OUT		DOLBY PROLOGIC
D. RANGE COMPRESSION		2-CH DOLBY SURROUND
		ON
		2-CH STEREO
		MULTI CHANNEL
SELECT	USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER

ANALOG OUT options

6 Use 5/∞ to select a desired analog output signal type.

You must set this item correctly when you play back a DVD VIDEO disc recorded with surround multichannel audio.

•When connecting with a surround decoder, select [2-CH DOLBY SURROUND].

•When connecting with a stereo amplifier/ receiver or television set, select [2-CH STEREO].

•When connecting the unit’s 5.1-channel input, select [MULTI CHANNEL].

7 Press ENTER.

The pull-down menu of the [DIGITAL AUDIO OUTPUT] appears.

DVD PLAYER SET UP
DIGITAL AUDIO OUTPUT		DOLBY DIGITAL/PCM
ANALOG OUT		PCM ONLY
		DOLBY PROLOGIC
		DOLBY DIGITAL/PCM
D. RANGE COMPRESSION		STREAM/PCM
SELECT	USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER

DIGITAL AUDIO OUTPUT options

16