Overview of commands in Framing Byte | Kathrein MSK 24 specification

Sat measurement

Example

0

SAT-CTRL LNB=1

V-SEC=2 DiSEqC=3

SAT-CTRL menu

DiSEqC-Framing

DiSEqC menu

DiSEqC-COMMAND E0 00 24 >

DiSEqC menu

Note

+

You want to test the Kathrein matrix EXR 22. The command set for the matrix EXR 22 is E0 00 24 (LNB High) and E0 00 20 (LNB Low).

Call up DiSEqC:

Press buttons [2ndF] [SAT-CTRL]

Press button [3] to call up the DiSEqC control.

You can now enter the data bits for each code word using the buttons [0] to [9] and [./S]. Send the control command by pressing [ENTER]. The > symbol indicates that the control command has been sent.

The command set to control the Kathrein matrix EXR 22 has been entered and sent.

You can find the DiSEqC command sets for the Kathrein matrices EXR 20, EXR 22 and the 9xx series in the Technical Appendix.

Overview of commands in Framing Byte

ë

HEX	Description
Byte
E0	Command from master, single transmission
E1	Command from master, repetitive transmission
E2	Command from master, answer expected, first transmission
E3	Command from master, answer expected, repeated
	transmission
E4	Answer from slave, "OK", no error detected
E5	Answer from slave, command not supported by slave
E6	Answer from slave, parity error detected
E7	Answer from slave, command not detected

27

Image 27

Kathrein MSK 24 manual Overview of commands in Framing Byte, Press buttons 2ndF SAT-CTRL

Contents

Satellite / TV / Radio Test Receiver MSK Page Validity of this manual Preface Contents Technical Appendix Spectrum measurement Parts supplied Explanation of symbolsSafety instructions General Notes How it operates Overview of functions Block diagram of MSK SAT Technical Data 10 V...20 V, max mA LC display Operating and display elementsDisplay elements Connections right side Overview of the keyboard commands Scart output ConnectionsRF input socket External DC voltage supply Software Accu LEV 48.5dBuV Switching on the receiverSwitching off the receiver Starting up Setup menu Setup menuFactory settings Settings in the setup menu Mains and battery operation Battery operationMains operation Standard Switch-Over Sat measurementPress 2ndF STD Overview of commands in Entering Frequency SAT Frequency Display and Entering FrequencyPress 1 5 0 8 E Nter LEV dBuV Level MeasurementLevel Overflow and Underflow LEV .dBuV Calling up the Scan function 2ndF Scan Switch over to Scan operationTracking Satellites Change the measuring range of the bar display Tracking for Single Frequencies Overview of commands in Tracking Audio Carrier Frequency Button Frequency in MHz Bandwidth in kHzPress 2ndF SC Press buttons 2ndF LNB LNB Voltage and 22 kHz / 60 Hz Switch-OverOverview of commands in LNB Voltage Example LNB14,0V 150mA LNB voltage Button Example LNB14,0V 22kHz 150mA Parity bit DiSEqC Digital Satellite Equipment Control Press buttons 2ndF SAT-CTRL Overview of commands in Framing Byte Hex byte Description Overview of commands in Address Byte Overview of commands in Command Byte Sat measurement Simple Tone Burst DiSEqC Overview of commands in Data ByteOrbit Switch position Data Position Overview of commands in Simple DiSEqC DiSEqC-SIMPLE Tone Burst Enter the letters A...F Button SEC Vario-Satellite Equipment Control2ndF SAT-CTRL Call up the V-SEC menu Enter the figures 0 to Overview of commands in Standard Switch-Over TV TV measurement=BG 2=L 3=DK =I 5=MN 6=M1 Enter the channel Switch over to TV receptionSwitch to special channel Channel Display and Entering Channel Then 1 7 5 ./S 2 5 Enter LEV.dBuV Level Measurement TV Press buttons 2ndF Level LEV-RANGE2 TV Example SC 5.50MHz LEV -13.0dB LEV 58.5dBuV Overview of commands in Measuring Audio Carrier FrequencyAudio Carrier Distance and Level Standard Audio carrier Nicam Nicam Measuring Audio Bit Error Rates Calling up Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 Then 9 9 ./S 2 5 Enter FM measurement2ndF FM Press 2ndF FM FR104,80MHz FM LEV¯¯¯.¯dBuV SAT-Full Spectrum measurementSat Spectrum TV Spectrum TV narrow Overview of commands in TV SpectrumFM Spectrum TV full Maintenance Changing the batteryCustomer service Signal-to-noise distance Technical Appendix+14.1 dB DiSEqC commands for Kathrein matrices Command set for Kathrein matrix 9xx-seriesCommand set for Kathrein matrix EXR VHF-CCIR UHF-CCIR Channel tables VHF UHF Channel and frequency table for L standard frequency in MHz III Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change