Overview of commands in Address Byte | Kathrein MSK 24 specs

Sat measurement

Overview of commands in Address Byte

	Hex byte	Description
	00	All equipment
	10	Every LNB, matrix or SMATV
	11	LNB
	12	LNB with loop-through
ë	14	Matrix (switcher)
	14	Matrix (switcher)
	15	Matrix (switcher) with loop-through
	18	SMATV
	20	Every polarizer
	21	Maximum rotation (full skew) with lineal polarization
	22	Set polarizer in steps
	30	Every positioner
	31	Polar / Azimuth positioner
	32	Elevation positioner
	33	Combined positioner
	34	LNB positioner
	40	Installation help
	41	Help to set signal strength
	60	Reserved for allocated addresses
	70	"Intelligent slave interface" for "Proprietary multi-
		master bus"
	71	Interface for users and checked head stations
	Fx	OEM expansion

28

Image 28

Kathrein MSK 24 manual Overview of commands in Address Byte, Hex byte Description

Contents

Satellite / TV / Radio Test Receiver MSK Page Preface Validity of this manual Contents Spectrum measurement Technical Appendix Explanation of symbols Safety instructionsGeneral Notes Parts supplied How it operates Overview of functions Block diagram of MSK Technical Data SAT 10 V...20 V, max mA Operating and display elements Display elementsConnections right side LC display Overview of the keyboard commands Connections RF input socketExternal DC voltage supply Scart output Switching on the receiver Switching off the receiverStarting up Software Accu LEV 48.5dBuV Setup menu Factory settingsSettings in the setup menu Setup menu Battery operation Mains and battery operationMains operation Sat measurement Standard Switch-OverPress 2ndF STD Frequency Display and Entering Frequency Overview of commands in Entering Frequency SATPress 1 5 0 8 E Nter Level Measurement Level Overflow and UnderflowLEV .dBuV LEV dBuV 2ndF Scan Switch over to Scan operation Tracking SatellitesChange the measuring range of the bar display Calling up the Scan function Overview of commands in Tracking Tracking for Single Frequencies Button Frequency in MHz Bandwidth in kHz Audio Carrier FrequencyPress 2ndF SC LNB Voltage and 22 kHz / 60 Hz Switch-Over Overview of commands in LNB Voltage Example LNB14,0V 150mALNB voltage Button Press buttons 2ndF LNB Example LNB14,0V 22kHz 150mA DiSEqC Digital Satellite Equipment Control Parity bit Overview of commands in Framing Byte Press buttons 2ndF SAT-CTRL Overview of commands in Address Byte Hex byte Description Overview of commands in Command Byte Sat measurement Overview of commands in Data Byte Orbit Switch position Data PositionOverview of commands in Simple DiSEqC Simple Tone Burst DiSEqC DiSEqC-SIMPLE Tone Burst SEC Vario-Satellite Equipment Control 2ndF SAT-CTRL Call up the V-SEC menuEnter the figures 0 to Enter the letters A...F Button TV measurement Overview of commands in Standard Switch-Over TV=BG 2=L 3=DK =I 5=MN 6=M1 Switch over to TV reception Switch to special channelChannel Display and Entering Channel Enter the channel Then 1 7 5 ./S 2 5 Enter Level Measurement TV LEV.dBuV LEV-RANGE2 TV Example Press buttons 2ndF Level Overview of commands in Measuring Audio Carrier Frequency Audio Carrier Distance and LevelStandard Audio carrier Nicam SC 5.50MHz LEV -13.0dB LEV 58.5dBuV Calling up Measuring Audio Bit Error Rates Nicam Measuring Audio Bit Error RatesSC 5.85 MHz BER=2.145E-05 FM measurement 2ndF FMPress 2ndF FM Then 9 9 ./S 2 5 Enter FR104,80MHz FM LEV¯¯¯.¯dBuV Spectrum measurement Sat SpectrumTV Spectrum SAT-Full Overview of commands in TV Spectrum FM SpectrumTV full TV narrow Changing the battery MaintenanceCustomer service Technical Appendix Signal-to-noise distance+14.1 dB Command set for Kathrein matrix 9xx-series DiSEqC commands for Kathrein matricesCommand set for Kathrein matrix EXR Channel tables VHF-CCIR UHF-CCIR Channel and frequency table for L standard frequency in MHz VHF UHF III Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change