Example, DiSEqC-SIMPLE Tone Burst | Kathrein MSK 24 specification

Sat measurement

Example

0

SAT-CTRL LNB=1

V-SEC=2 DiSEqC=3

SAT-CTRL menu

DiSEqC-Framing

DiSEqC menu

DiSEqC-SIMPLE
0 Tone BURST	>

Simple DiSEqC menu

Call up Simple DiSEqC:

Press buttons [2ndF] [SAT-CTRL]

Press button [3] to call up DiSEqC control.

The cursor must be positioned on the left with the [-]button. Press button

[0]or [1] to call up the Simple DiSEqC menu.

Press [ENTER] to send the control command. The > symbol indicates that the control command has been sent. Press button [1] to switch to data burst.

32

Image 32

Kathrein MSK 24 manual Example, DiSEqC-SIMPLE Tone Burst

Contents

Satellite / TV / Radio Test Receiver MSK Page Preface Validity of this manual Contents Spectrum measurement Technical Appendix Explanation of symbols Safety instructionsGeneral Notes Parts supplied How it operates Overview of functions Block diagram of MSK Technical Data SAT 10 V...20 V, max mA Operating and display elements Display elementsConnections right side LC display Overview of the keyboard commands Connections RF input socketExternal DC voltage supply Scart output Switching on the receiver Switching off the receiverStarting up Software Accu LEV 48.5dBuV Setup menu Factory settingsSettings in the setup menu Setup menu Mains operation Mains and battery operationBattery operation Press 2ndF STD Standard Switch-OverSat measurement Press 1 5 0 8 E Nter Overview of commands in Entering Frequency SATFrequency Display and Entering Frequency Level Measurement Level Overflow and UnderflowLEV .dBuV LEV dBuV 2ndF Scan Switch over to Scan operation Tracking SatellitesChange the measuring range of the bar display Calling up the Scan function Overview of commands in Tracking Tracking for Single Frequencies Press 2ndF SC Audio Carrier FrequencyButton Frequency in MHz Bandwidth in kHz LNB Voltage and 22 kHz / 60 Hz Switch-Over Overview of commands in LNB Voltage Example LNB14,0V 150mALNB voltage Button Press buttons 2ndF LNB Example LNB14,0V 22kHz 150mA DiSEqC Digital Satellite Equipment Control Parity bit Overview of commands in Framing Byte Press buttons 2ndF SAT-CTRL Overview of commands in Address Byte Hex byte Description Overview of commands in Command Byte Sat measurement Overview of commands in Data Byte Orbit Switch position Data PositionOverview of commands in Simple DiSEqC Simple Tone Burst DiSEqC DiSEqC-SIMPLE Tone Burst SEC Vario-Satellite Equipment Control 2ndF SAT-CTRL Call up the V-SEC menuEnter the figures 0 to Enter the letters A...F Button =BG 2=L 3=DK =I 5=MN 6=M1 Overview of commands in Standard Switch-Over TVTV measurement Switch over to TV reception Switch to special channelChannel Display and Entering Channel Enter the channel Then 1 7 5 ./S 2 5 Enter Level Measurement TV LEV.dBuV LEV-RANGE2 TV Example Press buttons 2ndF Level Overview of commands in Measuring Audio Carrier Frequency Audio Carrier Distance and LevelStandard Audio carrier Nicam SC 5.50MHz LEV -13.0dB LEV 58.5dBuV SC 5.85 MHz BER=2.145E-05 Nicam Measuring Audio Bit Error RatesCalling up Measuring Audio Bit Error Rates FM measurement 2ndF FMPress 2ndF FM Then 9 9 ./S 2 5 Enter FR104,80MHz FM LEV¯¯¯.¯dBuV Spectrum measurement Sat SpectrumTV Spectrum SAT-Full Overview of commands in TV Spectrum FM SpectrumTV full TV narrow Customer service MaintenanceChanging the battery +14.1 dB Signal-to-noise distanceTechnical Appendix Command set for Kathrein matrix EXR DiSEqC commands for Kathrein matricesCommand set for Kathrein matrix 9xx-series Channel tables VHF-CCIR UHF-CCIR Channel and frequency table for L standard frequency in MHz VHF UHF III Channel and frequency table for I standard frequency in MHz Technical Appendix Technical Appendix Technical Appendix Page 936.1997/ZWT/PF Technical data subject to change