Bottom View Pedal Unit | Kawai CE200 specs

Bottom View

Pedal Unit	(H)

(G)

(A)

(H)(C)

1.Insert the Adjuster (H) on the Pedal Unit.

2.Untie the pedal cable on the bottom of the Pedal Board (C).

3.Fasten the Side Panels (A) and the Pedal Board (C) with five screws (G) on both the left and right side of the instrument (totalling ten screws).

		(E)
	4. Hold the Back Board (B) behind the Pedal
	Board (C) and in front of the fixing metal of	(B)
	the Side Panels (A).	(B)
	the Side Panels (A).	(A)
	5. Fasten the Side Panels (A) and Back Board	(A)
	5. Fasten the Side Panels (A) and Back Board	(F)
	(B) with two screws (E) on both side of the
	instrument (totalling four screws).
	6. Fasten the Pedal Board (C) and Back
	Board (B) with four screws (F).

(C)

CAUTION:

To prevent personal injury, do not handle the main unit from the ends.

7.The next step requires one person on each end of the main unit. Grasp the unit with both hands, one under the front, the other under the rear (remember, not the end) and carefully center the main unit on top of the stand so that the hook brackets located on the bottom rear of the main unit are inside the stand side panels (A) and approximately one-third of the rear, top edge of the side panels are exposed. (See the illustration to the right)

8.Maintaining a firm grasp under the front of the main, unit slide it toward the rear of the stand until the hook brackets engage the brackets at the rear top of the side panels (A). This hook arrangement is design to prevent the main unit from tilting forward while the screws are installed. Keep one hand under the front of the main unit, push down on the front to be certain that hooks are properly engaged.

9.Fasten the main unit and the stand with four screws (D).

(D)

(A)

8	KAWAI DIGITAL PIANO CE200

Image 8

Kawai CE200 manual Bottom View Pedal Unit, Fasten the main unit and the stand with four screws D

Contents

CE200 Page Important Safety Instructions Indicates a potential hazard that could result in injury Instruction for AC power cord U.K Declaration of Conformity Thank YOU for Purchasing a Kawai Digital Piano Read ME FirstParts Provided Side Panel a Pcs Back Board B Pedal Board C Bottom View Pedal Unit Fasten the main unit and the stand with four screws D Attaching the Headphone Hook Piano Music Jacks Supplying AC Power Assembling the Stand Turning on the power Adjust the volume levelPlaying the Piano Pedals Press the Sound Select button under the name Selecting Another Preset SoundPlaying with More Sounds About Polyphony Value Buttons Entering Four Hands Mode Four Hands ModeSelecting Split Sounds Changing the Split Point Exiting Four Hands Mode Selecting Sounds in Four Hands ModeChanging Split Point Octave Shift for the Lower Section To ADD Reverb To ADD Other Effects Voicing NormalMellow Dynamic Starting the Metronome Changing the Time SignatureRhythm Metronome Metronome Adjusting the Metronome Volume Basics of the Recorder TWO-TRACK THREE-SONG RecorderRecorded Information Sound selection Pedal movements Recording Another Song Recording REC ButtonRecording Capacity Recorder and Metronome Press the PLAY/STOP button when you are finished recording Recording a Second Part Status of Song and Part Playing Back the Parts SeparatelyPlaying Back a Song PLAY/STOP Button Press the PLAY/STOP button again to stop play back Usingthe PLAY/STOP Buttonto Start Recording Erasing ALL the SongsErasing a Song Start flashing Piano Music Selecting the Touch Sensitivity Touch Button User Touch Transposing the Piano Transpose Button Tuning Multi Timbral ModeUser Memory / Factory Reset Brilliance Tuning BrillianceDamper Resonance Use the Value buttons to raise or lower the pitch About String Resonance String ResonancePress the Piano button while holding down the Touch Equal Temperament Piano only TemperamentBrief Explanation of Temperaments Pythagorean Temperament Meantone TemperamentWerckmeister III Temperament Kirnberger III Temperament Equal Temperament Flat KEY Signature of Temperament Lower Octave Shift Midi Channel Sending Program Change NumbersLocal Control ON/OFF Use the Value buttons to change the channel number MULTI-TIMBRAL Mode ON/OFF Transmit Program Change ON/OFFMulti-Timbral On On1 and On2 Multi-Timbral Off Channel Mute Lower Pedal ON/OFFThen use the Value buttons to turn them on and off Can not be selected Layer Octave Shift can be set between -2 to Layer Octave ShiftLayer Dynamics User Memory / Factory Reset Following settings can be savedFactory Reset Damper Hold Function Buttons What is MIDI? Understanding MidiMidi Jacks Midi Channel Bass Using the CE200 Piano AS Controller Midi ConnectionChanging Transmitting Channel Electric Piano button while holding down the Touch Program Change Audio ConnectionNow You’re ready to play Local Control Buttons Using the CE200 Piano AS a MULTI-TIMBRAL Sound Module MULTI-TIMBRAL Mode Using Midi Windows 2000 / 98SE users About a USB DriverWindows XP / Me users Macintosh OS X users Users of Macintosh OS9 or earlier Line OUT Jacks Bottom View Jacks Program Change Number Mapping Rhythm Style List Piano Music List Front Panel Sound Demo Song List Specifications Midi Exclusive Data Format Midi Implementation Chart Kawai Digital Piano Model CE200 Eng