Before Using Your Range

Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only)

Your range is shipped with the Burner Heads and Burner Caps in the correct locations. the Burner Heads and Burner Skirts.

1.Be sure to follow the Installation Instructions before installing and using your new range.

2.

Remove all packing tape from cooktop area. Remove all

 

I

 

 

 

 

 

Burner Caps and Burner Heads.

 

 

Burner

 

3.

Discard all packing

material located

under Burner Heads.

 

Cap

 

 

 

 

4.

To replace Burner

Heads & Caps, match the letters

 

 

 

 

located under center of Burner Caps with the letters

 

 

 

 

located inside Burner Heads (Fig. 1).

3urner

(

)_

5.

Match the letters stamped on Burner Skirts with Burner

Head

1_ _::D_. _?://

 

Heads and Burner Caps (See Fig. 1). Replace the Burner

 

 

::

 

 

Heads and Caps on cooktop (See Fig. 2). Carefully align

 

 

 

 

 

 

 

the Electrodes into slot or hole of each Burner Head (Fig.

 

 

 

 

3). Note: The Burner Heads should

sit flat on Cooktop

_.

BumerS-k_t

j

 

Burner Skirts.

 

 

Fig.1

 

 

6.

Unpack Burner Grates and position

on the cooktop.

 

 

 

Packing material is located between

Fig. 2

 

Electrodes

must

 

align into slot or hole for each

Fig. 3

Burner

Head

Assembly of Burner Heads & Burner Caps (for Ceramic Glass Cooktop models only)

;_,

Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between the Burner Heads and Burner Skirts.

1.

Be sure to follow the Installation Instructions before

 

installing and using your new range.

2.

Remove all packing tape from cooktop. Remove Burner

 

Caps and Burner Heads (See Fig. 4).

3.

Discard all packing material located under all Burner

 

Heads.

8ridg_ B urner

3 p_sltlon_

:

_'S %: (notm_rked)

A

I

Burner

Cap

4. To replace Burner Heads & Caps, match the letters

located under center of Burner Caps with the letters

located inside Burner Head (only positions A & F are

marked with letters - See Fig. 5). Place all Burner Heads

& Caps on the cooktop (See Fig. 4) while carefully

aligning the Electrodes into slots or holes of the Burner

Heads (Fig. 7). Note: The Burner Heads should sit flat on

Cooktop Burner Skirts.

5. Replace Bridge Burner Caps. These include one Bridge

Burner Center Cap (rectangular shaped) and the two

Bridge Burner End Caps (The Bridge Burner End Caps will

fit either the front or rear Bridge Burner Head locations).

Make sure that the tabs located under the Bridge Burner

Caps fall into the slots located in the Bridge Burner Head

(See arrows in Fig. 6) and that all the Bridge Burner Caps

lie flat and evenly on the Bridge Burner Head.

6. Unpack Burner Grates. NOTE: Do not force End Burner

Grates down on cooktop. Be careful to line up the 2 Grate

Pins located on each of the 2 End Burner Grates into the

Pilot holes located on top of the Burner Caps (See Fig. 8).

Position Burner Grates on cooktop and check that all the

Burner Grate legs lie on the glass surface.

7. Place Center Burner Grate between the end Burner

Grates.

9k!:iiN] t_ :,3)

............. 7.2k

ii

Fig. 4

Bridg I Burner Head

Bridge

Burner

End

Cap

Bridge

Burner

Center

Cap

Bridge

Burner

End

Cap

!:. Burner Sk_rirt

R 5_

must align into slot or hole for each Burner Head

Fig. 7

Fig. 6

Fig. 8

Page 7
Image 7
Kenmore 790.7936, 790.7937 manual Before Using Your Range, 9k!iiN t ,3