Alternate Parts
Parts listed are available from your local Sears store or Sears Service Center. For further information, call
If You Have: | You Will Need to Buy: |
| |||||||
Laundry tub or | Sump pump | system | (if not already | ||||||
standpipe | taller | available) |
|
|
|
|
|
| |
than 96" (2.4 m) |
|
|
|
|
|
|
| ||
1" (2.5 cm) | 2" (5 cm) | diameter | to | 1" (2.5 cm) | |||||
diameter | standpipe | diameter | standpipe | adapter, | |||||
|
|
| Part Number 3363920 and connector kit | ||||||
|
|
| Part Number 285835 |
|
| ||||
Overhead | sewer | Standard | 20 gal. (76 L) 39" (99 cm) tall | ||||||
|
|
| drain tub or utility sink, sump pump and | ||||||
|
|
| connectors | (available | from local | ||||
|
|
| plumbing | suppliers) |
|
|
| ||
Floor | drain | Siphon break, Part Number 285834; | |||||||
|
|
| additional | drain | hose, |
|
| ||
|
|
| Part Number 8318155 and connector kit, | ||||||
|
|
| Part Number 285835 |
|
| ||||
Water | faucets | 2 longer | water | fill hoses: |
| ||||
beyond reach of fill | 6 ft (1.8 m) Part Number | 76314, | |||||||
hoses |
|
| 10 ft (3.0 m) Part Number | 350008 | |||||
Lint clogged drain | Drain protector, | Part | Number 367031 | ||||||
Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."
Your washer can be installed in a basement, laundry room, closet, or recessed area. See "Drain System."
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need"
•A water heater set to deliver 120°F (49°C) water to the washer.
•A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements."
•Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of
•A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.
•A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for information on winterizing.
Installation spacing for recessed area and closet installations
The following spacing dimensions are recommended for this washer. This washer has been tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:
•Additional spacing should be considered for ease of installation and servicing.
Additional spacing should be considered on all sides of the washer to reduce noise transfer.
For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
Companion appliance spacing should also be considered.
_! 3"*
(7.6crn)
_ | _ 3"* |
(7.6cm)
C
A. Front view
B. Side view
C. Closet door with vents
*Required spacing
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See "Tools and Parts."
Standpipe drain system--wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum
The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer.
39"
(99 cm)
AB
