Cabinet Cutout Dimensions
Enclosure and clearance dimensions that are shown must be used. Given dimensions provide required clearances.
The installation of this grill must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2.
Copies of the standards listed may be obtained from:
CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio
NOTE: The grill drops into the opening and is supported by its side flanges. Do not use a bottom support.
The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all
C
C
|
|
|
| . |
|
|
| .5 cm) | min |
12" |
|
| ||
| accessory | |||
|
| (30 |
| |
to | any |
|
| |
|
|
|
| |
|
|
| . | |
| .6 cm) | min | ||
|
| |||
3" | (7 | hood | ||
open | ||||
to |
|
| ||
|
|
| ||
| E |
| . |
12" | min |
any | |
to |
|
accessory | |
D |
|
E
K 
|
|
|
|
| Warming | |
|
| " |
|
| Drawer | |
|
|
|
| |||
|
|
|
|
|
| |
|
|
|
|
|
| |
| ¹⁄₈ |
|
|
|
| |
9 |
|
|
|
|
| |
.2 cm) |
|
| ||||
(23 |
|
|
|
|
|
|
|
|
| K |
| J | |
|
|
| . |
|
| |
|
|
|
|
| ||
| 5" |
|
| |||
| min |
|
| |||
.7 | cm) |
|
| |||
|
|
|
| |||
(12 |
|
|
|
|
|
|
B
|
|
|
| Grills | or |
|
| Centers | |||
|
|
|
|
|
|
|
|
|
| ||
Side |
|
|
| Refreshment |
|
| |||||
| D |
|
|
|
|
|
|
|
|
| |
or |
|
|
|
|
|
|
|
|
|
| |
Sear |
|
|
|
|
|
|
|
|
|
|
|
Burners |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Access | Doors | ||||
|
|
|
|
|
|
|
| ||||
|
|
|
| .0 cm) |
|
|
| ||||
Utility |
|
| " | (53 |
|
|
|
|
|
|
|
|
| ⁷⁄₈ |
|
|
|
|
|
|
|
| |
or | 20 |
|
|
|
|
|
|
|
|
| |
Trash |
|
|
|
|
|
|
|
|
|
|
|
Drawer |
|
|
|
|
|
|
|
|
|
| L |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| min | . |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| " | (6 | .4 | cm) |
| ||
|
|
|
| 2¹⁄₂ |
|
|
| ||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |
K
KF
M
|
|
|
|
|
|
|
|
|
|
|
| A |
|
|
| 1¹⁄₂ | " | min | . | H |
| ||||
|
|
| ||||||||||
|
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| ||||||
| (3 | .8 | cm) |
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
|
| .4 cm) |
|
|
|
| ||||||
| " (52 |
|
|
|
|
|
|
|
|
|
| |
⁵⁄₈ |
|
|
|
|
|
|
|
|
|
|
| |
20 |
|
|
|
|
|
|
|
|
|
|
|
|
| Refrige | rato | r | |||||||||
| or |
| Maker |
|
|
|
| |||||
| Ice |
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| |||
K
G
Minimum Spacing Requirement Between Cutouts - Dimension K
Between 2 or more sets of Access Doors adjacent to each other:
K = 14" (35.6 cm) when 2 adjacent doors are opened to 90 degrees
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a set of Access Doors and a Trash Drawer, Utility Drawer, Warming Drawer, Refrigerator, or Ice Maker:
K = 8" (20.3 cm) when 1 of the adjacent doors is opened to 90 degrees
Between a Trash Drawer, Utility Drawer, or Warming Drawer:
K = 3" (7.6 cm)
7
