Using the Scanner, Turning the scanner on | Kodak i1800 Series

3 Using the Scanner

3 Using the Scanner

Turning the scanner on

This chapter provides the following operational procedures:

•Turning on/off the scanner

•Starting and stopping the scanner

•Document preparation

•Adjusting the input elevator

•Adjusting the output tray

•Adjusting the height of the scanner

•Scanning documents

•Automatic, continuous and manual feeding

•Using the touchscreen

The i1800 Series Scanners have two power switches. The main breaker switch is located on the back of the scanner on the lower left- side near the power cord.

1.Turn on the main breaker switch first. Under normal circumstances the main breaker switch should remain on.

2.After turning on the main breaker switch, press the power switch on the left side of the scanner to the on position (I).

A-61555 March 2007

3-1

Image 17

Kodak i1800 Series manual Using the Scanner, Turning the scanner on

Contents

A-61555 i1800 Series ScannersUser’s Guide A-61555March Contents A-61555March Appendix B Appendix A 1 Introduction Scanner features Supporting documentation System requirements Phone numbers •United States and Canada Contacting Service and Support User precautions Safety informationMSDS Gas springs warning EMC statements European UnionEnvironmental information United States Acoustic emission Power systemconnection Peoples Republic of Scanner components Front view 2 Getting Started 11Exit deflector — aids in document stacking 15 18 A-61555March Internal components Rear view Turning the scanner on 3 Using the Scanner A-61555March Starting and stopping scanning Turning the scanner offDocument preparation Materials A-61555March Selecting your feeding Adjusting the input elevatorposition Locking the side guides Adjusting the input tray for document length Adjusting the height of the input elevator Installing the document Adjusting the output trayAdjusting the side guides Output tray options 1 2 3 Positioning the output tray Adjusting the angle of the output tray Adjusting the end stop 3-10 The exit deflector 34 in Adjusting the output trayfor documents from 1.Remove the end stop on the output tray Adjusting the short document tray3. Adjust the sides guides as necessary Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetection Continuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screen Selecting the tone Selecting a language addressing for Enabling/disabling imageScanner only cycle the scanner 3-24 4.Restart the scanner Image Calibration UDDS Calibration Image Address information Idle screen Operator Log information Accessing scanner Count only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scanner Resuming from Power Saver mode Power Saver mode Viewing messages Enhanced Printer overview 4 The Enhanced Printer and Patch Readers Printer specifications Changing the front horizontal print position Changing print positions horizontal print position Changing the rear 3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 9.Replace the ink blotter strip cover 7.Press the blotter strip firmly into the channel10.Close the pod 4-10 Replacing the rear blotter strips The Patch Readers Patch function overviewPatch types they are not to spec Toggle Patch Patch code placement 5 Maintenance •Kodak Digital Science Roller Cleaning Pads Cleaning frequency chartCleaning tools and materials Ordering parts Supplies, consumables and accessories3E9575 9E3357 Vacuuming the output tray and input elevator Cleaning proceduresCleaning the OCP touchscreen Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires 14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport area guides — basic cleaning Cleaning the imaging Upper imaging guide Cleaning the imaging guides — thorough cleaning Lower imaging guide Running a transport cleaning sheet Final cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod separation pad Replacing the preReplacing the imaging guides Accessing the Operator Log from the touchscreen 6 TroubleshootingAccessing the Operator Log 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN 6. Select Device 5. From the main screen, click SettingsThe Settings screen will be displayed Use the button to create a compressed log package The Device screen will be displayed8.Select the Logs tab Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed listing Numerical messageerror condition 6-10 phone numbers and detailed information Contacting Service 6-12 Problem solving Calibration has failed Ultralightweight Paper Feed Module Appendix A AccessoriesBackground Accessory Kodak Manual Feeder Resolution Printer Accessory Appendix B Specifications Kodak, 2007. All rights reserved. TM Kodak Eastman Kodak Company 343 State StreetRochester, NY 14650 U.S.A