Manuals / Kodak / Computer Equipment / Scanner

Kodak i1800 Series manual A-61555March

Models: i1800 Series

1 101

Download 101 pages 19.43 Kb

Page 18

Manual background

After you power up the scanner, the following screen will be displayed.

When the scanner completes the power-up sequence, the Idle screen will be displayed. See the section entitled, Using the touchscreen” later in this chapter for information about the Idle screen.

IMPORTANT: Always power up the host computer to its ready state before powering up the scanner.

3-2	A-61555 March 2007

Image 18

Kodak i1800 Series manual A-61555March

Contents

i1800 Series Scanners User’s GuideA-61555 Contents A-61555MarchA-61555March Appendix A Appendix B1 Introduction Scanner features System requirements Supporting documentationContacting Service and Support Phone numbers •United States and CanadaMSDS Safety informationUser precautions Gas springs warningEnvironmental information European UnionEMC statements United Statesconnection Power systemAcoustic emission Peoples Republic of2 Getting Started Scanner components Front view15 18 11Exit deflector — aids in document stackingA-61555March Internal components Rear view 3 Using the Scanner Turning the scanner onA-61555March Document preparation Turning the scanner offStarting and stopping scanning MaterialsA-61555March position Adjusting the input elevatorSelecting your feeding Locking the side guidesAdjusting the height of the input elevator Adjusting the input tray for document lengthAdjusting the side guides Adjusting the output trayInstalling the document Output tray optionsPositioning the output tray 1 2 3Adjusting the end stop Adjusting the angle of the output tray3-10 A-61555MarchThe exit deflector Adjusting the output tray for documents from34 in 1.Remove the end stop on the output tray Adjusting the short document tray3. Adjust the sides guides as necessary A-61555MarchAdjusting the height of the scanner Feeding documents using multi-feeddetection Automatic feedingContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3.Touch Close to return to the Settings screen 3-20A-61555March Selecting the tone Selecting a language Scanner only Enabling/disabling imageaddressing for cycle the scanner4.Restart the scanner 3-24A-61555March Image Calibration UDDS Calibration Idle screen Image Address informationOperator Log Accessing scanner informationCount only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Automatically pausing and resuming the scanner Manually pausing and resuming the scannerPower Saver mode Viewing messages Resuming from Power Saver mode4 The Enhanced Printer and Patch Readers Enhanced Printer overviewPrinter specifications A-61555MarchChanging print positions Changing the front horizontal print positionChanging the rear horizontal print position3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test A-61555MarchReplacing the front blotter strips 10.Close the pod 7.Press the blotter strip firmly into the channel9.Replace the ink blotter strip cover 4-10Replacing the rear blotter strips Patch types Patch function overviewThe Patch Readers they are not to specPatch code placement Toggle Patch5 Maintenance Cleaning frequency chart Cleaning tools and materials•Kodak Digital Science Roller Cleaning Pads 3E9575 Supplies, consumables and accessoriesOrdering parts 9E3357Cleaning procedures Cleaning the OCP touchscreenVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires 9. Lift up the printer access coverA-61555March 14. Close the printer access cover Vacuuming the transport area Vacuuming under the background stripsCleaning the imaging guides — basic cleaningCleaning the imaging guides — thorough cleaning Upper imaging guideLower imaging guide cleaning sheet Running a transportFinal cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod Replacing the imaging Replacing the preseparation pad guides6 Troubleshooting Accessing the Operator LogAccessing the Operator Log from the touchscreen 2.From the Driver Types box, select TWAIN 4. Select the Scanner iconA-61555March 6. Select Device 5. From the main screen, click SettingsThe Settings screen will be displayed A-61555MarchUse the button to create a compressed log package The Device screen will be displayed8.Select the Logs tab A-61555MarchMessage listing A-61555MarchA-61555March Input elevator too full, feed module A-61555March UDDS calibration failed error condition Numerical messagelisting 6-10Contacting Service phone numbers and detailed informationA-61555March Problem solving 6-12A-61555March Calibration has failed Background Accessory Kodak Manual Feeder Appendix A AccessoriesUltralightweight Paper Feed Module Resolution Printer AccessorySpecifications Appendix BEastman Kodak Company 343 State Street Rochester, NY 14650 U.S.AKodak, 2007. All rights reserved. TM Kodak