Power Saver mode Viewing messages | Kodak i1800 Series specification

Power Saver mode

Power Saver mode

Viewing messages

The Kodak i1800 Series Scanners are configured from the factory to go into Power Saver mode after 15 minutes of inactivity. This setting can be changed by your capture software application. If Power Saver is enabled, the scanner will begin a one-minute count-down prior to entering Power Saver mode. When the scanner is in Power Saver mode, the green LED will be flashing and the touchscreen will be blank.

NOTE: If you do not want to go into Power Saver mode, touch Cancel.

Resuming from Power Saver mode

•If there is paper in the input elevator, take the paper out and put it back in.

•If no paper is in the input elevator, put paper in the input elevator. The initializing screen will appear on the touchscreen.

The message window provides an up-to-date status of scanner activity and/or any operator messages. Only one message can be displayed at a time. To review previous messages use the Operator Log.

3-36	A-61555 March 2007

Image 52

Kodak i1800 Series manual Power Saver mode Viewing messages, Resuming from Power Saver mode

Contents

User’s Guide i1800 Series ScannersA-61555 Contents A-61555March A-61555March Appendix A Appendix B 1 Introduction Scanner features System requirements Supporting documentation Contacting Service and Support Phone numbers •United States and Canada Safety information User precautionsMSDS Gas springs warning European Union EMC statementsEnvironmental information United States Power system Acoustic emissionconnection Peoples Republic of 2 Getting Started Scanner components Front view 15 18 11Exit deflector — aids in document stacking A-61555March Internal components Rear view 3 Using the Scanner Turning the scanner on A-61555March Turning the scanner off Starting and stopping scanningDocument preparation Materials A-61555March Adjusting the input elevator Selecting your feedingposition Locking the side guides Adjusting the height of the input elevator Adjusting the input tray for document length Adjusting the output tray Installing the documentAdjusting the side guides Output tray options Positioning the output tray 1 2 3 Adjusting the end stop Adjusting the angle of the output tray 3-10 The exit deflector for documents from Adjusting the output tray34 in 3. Adjust the sides guides as necessary Adjusting the short document tray1.Remove the end stop on the output tray Adjusting the height of the scanner Feeding documents using multi-feeddetection Automatic feeding Continuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3.Touch Close to return to the Settings screen 3-20 Selecting the tone Selecting a language Enabling/disabling image addressing forScanner only cycle the scanner 4.Restart the scanner 3-24 Image Calibration UDDS Calibration Idle screen Image Address information Operator Log Accessing scanner information Count only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Automatically pausing and resuming the scanner Manually pausing and resuming the scanner Power Saver mode Viewing messages Resuming from Power Saver mode 4 The Enhanced Printer and Patch Readers Enhanced Printer overview Printer specifications Changing print positions Changing the front horizontal print position Changing the rear horizontal print position 3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 7.Press the blotter strip firmly into the channel 9.Replace the ink blotter strip cover10.Close the pod 4-10 Replacing the rear blotter strips Patch function overview The Patch ReadersPatch types they are not to spec Patch code placement Toggle Patch 5 Maintenance Cleaning tools and materials Cleaning frequency chart•Kodak Digital Science Roller Cleaning Pads Supplies, consumables and accessories Ordering parts3E9575 9E3357 Cleaning the OCP touchscreen Cleaning proceduresVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires 9. Lift up the printer access cover 14. Close the printer access cover Vacuuming the transport area Vacuuming under the background strips Cleaning the imaging guides — basic cleaning Cleaning the imaging guides — thorough cleaning Upper imaging guide Lower imaging guide cleaning sheet Running a transport Final cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod Replacing the pre separation padReplacing the imaging guides Accessing the Operator Log 6 TroubleshootingAccessing the Operator Log from the touchscreen 2.From the Driver Types box, select TWAIN 4. Select the Scanner icon The Settings screen will be displayed 5. From the main screen, click Settings6. Select Device 8.Select the Logs tab The Device screen will be displayedUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed Numerical message listingerror condition 6-10 Contacting Service phone numbers and detailed information Problem solving 6-12 Calibration has failed Appendix A Accessories Ultralightweight Paper Feed ModuleBackground Accessory Kodak Manual Feeder Resolution Printer Accessory Specifications Appendix B Rochester, NY 14650 U.S.A Eastman Kodak Company 343 State StreetKodak, 2007. All rights reserved. TM Kodak