Open the top access cover | Kodak i1800 Series specs

Moving the printer carrier and cable from rear position to the front position

NOTE: Remove the ink cartridge before you begin. See the next section “Replacing the ink cartridge” for procedures.

1.Open the top access cover.

2.Disconnect the ribbon cable.

3.Remove the printer carrier.

4.Close the top access cover.

5.Remove the output tray and open the printer access cover.

6.Install the printer carrier in the desired position.

7.Connect the ribbon cable.

8.Install the ink cartridge.

9.Close the top access cover.

10.Restart the scanner.

11.Run a print test.

4-6	A-61555 March 2007

Image 58

Kodak i1800 Series manual Open the top access cover

Contents

User’s Guide i1800 Series ScannersA-61555 Contents A-61555March A-61555March Appendix A Appendix B 1 Introduction Scanner features System requirements Supporting documentation Contacting Service and Support Phone numbers •United States and Canada MSDS Safety informationUser precautions Gas springs warning Environmental information European UnionEMC statements United States connection Power systemAcoustic emission Peoples Republic of 2 Getting Started Scanner components Front view 15 18 11Exit deflector — aids in document stacking A-61555March Internal components Rear view 3 Using the Scanner Turning the scanner on A-61555March Document preparation Turning the scanner offStarting and stopping scanning Materials A-61555March position Adjusting the input elevatorSelecting your feeding Locking the side guides Adjusting the height of the input elevator Adjusting the input tray for document length Adjusting the side guides Adjusting the output trayInstalling the document Output tray options Positioning the output tray 1 2 3 Adjusting the end stop Adjusting the angle of the output tray 3-10 The exit deflector for documents from Adjusting the output tray34 in 3. Adjust the sides guides as necessary Adjusting the short document tray1.Remove the end stop on the output tray Adjusting the height of the scanner Feeding documents using multi-feeddetection Automatic feeding Continuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3.Touch Close to return to the Settings screen 3-20 Selecting the tone Selecting a language Scanner only Enabling/disabling imageaddressing for cycle the scanner 4.Restart the scanner 3-24 Image Calibration UDDS Calibration Idle screen Image Address information Operator Log Accessing scanner information Count only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Automatically pausing and resuming the scanner Manually pausing and resuming the scanner Power Saver mode Viewing messages Resuming from Power Saver mode 4 The Enhanced Printer and Patch Readers Enhanced Printer overview Printer specifications Changing print positions Changing the front horizontal print position Changing the rear horizontal print position 3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 10.Close the pod 7.Press the blotter strip firmly into the channel9.Replace the ink blotter strip cover 4-10 Replacing the rear blotter strips Patch types Patch function overviewThe Patch Readers they are not to spec Patch code placement Toggle Patch 5 Maintenance Cleaning tools and materials Cleaning frequency chart•Kodak Digital Science Roller Cleaning Pads 3E9575 Supplies, consumables and accessoriesOrdering parts 9E3357 Cleaning the OCP touchscreen Cleaning proceduresVacuuming the output tray and input elevator Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires 9. Lift up the printer access cover 14. Close the printer access cover Vacuuming the transport area Vacuuming under the background strips Cleaning the imaging guides — basic cleaning Cleaning the imaging guides — thorough cleaning Upper imaging guide Lower imaging guide cleaning sheet Running a transport Final cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod Replacing the imaging Replacing the preseparation pad guides Accessing the Operator Log 6 TroubleshootingAccessing the Operator Log from the touchscreen 2.From the Driver Types box, select TWAIN 4. Select the Scanner icon The Settings screen will be displayed 5. From the main screen, click Settings6. Select Device 8.Select the Logs tab The Device screen will be displayedUse the button to create a compressed log package Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed error condition Numerical messagelisting 6-10 Contacting Service phone numbers and detailed information Problem solving 6-12 Calibration has failed Background Accessory Kodak Manual Feeder Appendix A AccessoriesUltralightweight Paper Feed Module Resolution Printer Accessory Specifications Appendix B Rochester, NY 14650 U.S.A Eastman Kodak Company 343 State StreetKodak, 2007. All rights reserved. TM Kodak