Performing a Print test | Kodak i1800 Series specification

Performing a Print test

Performing a Print test	The print test checks to be sure the ink jets in the Enhanced Printer are
	working properly.
	1. Touch Print Test. The Print Test screen will be displayed.

2.Place a blank sheet(s) of paper in the input elevator.

3.Touch OK. The document(s) in the output tray will display the results of the print test.

4.Remove the document(s) from the output tray and evaluate the appearance of the test pattern.

•If the pattern is complete, you are ready to begin.

•If the pattern is not legible:

−Check to see that the print cartridge is installed properly. Repeat the print test. See Chapter 4, Using the Enhanced Printer and Patch Readers.

−If the pattern is still not legible, replace the ink cartridge.

5.Touch End Job to return to the Idle screen.

A-61555 March 2007

3-31

Image 47

Kodak i1800 Series manual Performing a Print test

Contents

A-61555 i1800 Series ScannersUser’s Guide A-61555March Contents A-61555March Appendix B Appendix A 1 Introduction Scanner features Supporting documentation System requirements Phone numbers •United States and Canada Contacting Service and Support Gas springs warning Safety informationUser precautions MSDS United States European UnionEMC statements Environmental information Peoples Republic of Power systemAcoustic emission connection Scanner components Front view 2 Getting Started 11Exit deflector — aids in document stacking 15 18 A-61555March Internal components Rear view Turning the scanner on 3 Using the Scanner A-61555March Materials Turning the scanner offStarting and stopping scanning Document preparation A-61555March Locking the side guides Adjusting the input elevatorSelecting your feeding position Adjusting the input tray for document length Adjusting the height of the input elevator Output tray options Adjusting the output trayInstalling the document Adjusting the side guides 1 2 3 Positioning the output tray Adjusting the angle of the output tray Adjusting the end stop 3-10 The exit deflector 34 in Adjusting the output trayfor documents from 1.Remove the end stop on the output tray Adjusting the short document tray3. Adjust the sides guides as necessary Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feeddetection Continuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen 3-20 3.Touch Close to return to the Settings screen Selecting the tone Selecting a language cycle the scanner Enabling/disabling imageaddressing for Scanner only 3-24 4.Restart the scanner Image Calibration UDDS Calibration Image Address information Idle screen Operator Log information Accessing scanner Count only mode Performing a Print test Performing a self test Scanning Using function keys when scanning Manually pausing and resuming the scanner Automatically pausing and resuming the scanner Resuming from Power Saver mode Power Saver mode Viewing messages Enhanced Printer overview 4 The Enhanced Printer and Patch Readers Printer specifications Changing the front horizontal print position Changing print positions horizontal print position Changing the rear 3.Lift the printer carrier out of position 1.Open the top access cover Replacing the ink cartridge 9.Run a print test Replacing the front blotter strips 4-10 7.Press the blotter strip firmly into the channel9.Replace the ink blotter strip cover 10.Close the pod Replacing the rear blotter strips they are not to spec Patch function overviewThe Patch Readers Patch types Toggle Patch Patch code placement 5 Maintenance •Kodak Digital Science Roller Cleaning Pads Cleaning frequency chartCleaning tools and materials 9E3357 Supplies, consumables and accessoriesOrdering parts 3E9575 Vacuuming the output tray and input elevator Cleaning proceduresCleaning the OCP touchscreen Cleaning the rollers Cleaning the separation roller tires 9. Lift up the printer access cover Cleaning the feed module tires 14. Close the printer access cover Vacuuming under the background strips Vacuuming the transport area guides — basic cleaning Cleaning the imaging Upper imaging guide Cleaning the imaging guides — thorough cleaning Lower imaging guide Running a transport cleaning sheet Final cleaning steps Replacement procedures •Close the pod and the printer access cover 7.Remove one core assembly 15.Close the pod 1.Open the pod guides Replacing the preseparation pad Replacing the imaging Accessing the Operator Log from the touchscreen 6 TroubleshootingAccessing the Operator Log 4. Select the Scanner icon 2.From the Driver Types box, select TWAIN 6. Select Device 5. From the main screen, click SettingsThe Settings screen will be displayed Use the button to create a compressed log package The Device screen will be displayed8.Select the Logs tab Message listing A-61555March Input elevator too full, feed module A-61555March UDDS calibration failed 6-10 Numerical messagelisting error condition phone numbers and detailed information Contacting Service 6-12 Problem solving Calibration has failed Resolution Printer Accessory Appendix A AccessoriesUltralightweight Paper Feed Module Background Accessory Kodak Manual Feeder Appendix B Specifications Kodak, 2007. All rights reserved. TM Kodak Eastman Kodak Company 343 State StreetRochester, NY 14650 U.S.A