Manuals / Kohler / Lawn and Garden / Portable Generator

Kohler 14/20RESAL manual If the exerciser has not been set, No Exercise Sch will be displayed

Models: 14/20RESAL 14/20RESA

1 72

Download 72 pages 24.65 Kb

Page 35

* If the exerciser has not been set, No Exercise Sch will be displayed.

Genset ---->

System

System Freq:

XX.X Hz

System Phase

System Volt

Battery V:

HOLD:

Next Exercise *

HR:MN PM MM/DD/YY

HOLD:

Exercise Mode:

Loaded

HOLD:

Exercise Freq:

Weekly

Language:

Contrast:

50

Next Exercise

HR:MN PM MM/DD/YY

Exercise Mode:

Unloaded Cycle/Unloaded Full/ Loaded Full

Exercise Freq:

Weekly/Bi-Weekly

<---- Return

tp6804

* If the exerciser has not been set, No Exercise Sch will be displayed.

Figure 3-8 Procedure to Set the Exerciser on the RDC2 Controller

TP-6804 12/11

Section 3 RDC2 Controller Operation 35

Image 35

Kohler 14/20RESAL manual If the exerciser has not been set, No Exercise Sch will be displayed

Contents

Operation ModelsControllers TP-6804 12/11Engine Identification Product Identification InformationController Identification Generator Set Identification NumbersTP-6804 12/11 Table of ContentsUnloaded Cycle Exercise with Complete System Diagnostics ExerciseTable of Contents, continued Table of Contents, continued TP-6804 12/11 Accidental Starting Safety Precautions and InstructionsBattery Exhaust System Engine Backfire/Flash FireWARNINGCAUTION Fuel SystemHazardous Noise Hazardous Voltage/ Moving PartsHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance TP-6804 12/11 14 Service Assistance1.2 Engine Section 1 Descriptions and Service Views1.5 Transfer Switch 1.1 IntroductionRDC2 Controller Features DC2 Controller Features 1.7.3 OnCue Home Generator Management System 1.7 Accessories1.7.1 Carburetor Heater 1.7.2 Fuel Regulator Heater 20RESA and RESAL onlyFigure 1-2 Service View Model 20RESA shown 1.8 Service ViewsTP-6804 12/11 20 Section 1 Descriptions and Service Views2.3 Generator Set Operation 2.1 Prestart ChecklistSection 2 Generator Set Operation 2.2 Exercising the Generator Set2.3.7 Automatic Operation with Model RDT or RSB Transfer Switches 2.3.6 Automatic Operation with Model RXT Transfer Switch2.4 Exercise 2.4.1 Setting the Exerciser2.4.2 Unloaded Cycle Exercise with Complete System Diagnostics 2.4.3 Unloaded Full-Speed Exercise 2.5 Faults2.4.5 Power Failure During Exercise Cycle 2.5.3 ATS Communication Errors2.5.4 Resetting the Controller after a Fault Shutdown Warning W or Figure 2-3 Controller Fault Messages TP-6804 12/11 28 Section 2 Generator Set OperationSection 3 RDC2 Controller Operation 3.1 RDC2 Generator Set/ Transfer Switch Controller3.2 Controls and Indicators 3.2.1 Controller Keypad 3.2.2 LED Indicators3.2.3 LCD Display 3.5 Changing Settings 3.3 Controller Power3.4 Battery Charging Repeat steps 5 and 6, using the arrow and select When the correct date is shown, press the Select3.6.2 Changing the Exercise Settings 3.6 Setting the Exerciser3.6.1 Setting the Exerciser at Controller Power--up If the exerciser has not been set, No Exercise Sch will be displayed Figure 3-8 Procedure to Set the Exerciser on the RDC2 Controller3.8 Main Menu 3.7 RDC2 Controller Menus3.10 Engine Metering Menu 3.9 Overview MenuDANGER 3.11 Generator Metering Menu3.13 Genset Run Time Menu 3.12 Generator Set Information Menu3.14 Genset System Menu 3.15 ATS Status Menu 3.16 ATS Configuration Menu 3.18 Networking Information Menus 3.17 Date and Time Menu3.18.1 Networking Status Submenu 3.18.2 Networking Configuration Submenu OnCue Password 3.18.3 RBUS Information 3.18.4 Remote Devices Submenu 3.19 Programmable Interface Module PIM Status Menu 3.20 Load Control Module LCM Menus 3.21 Event Log Section 4 DC2 Controller Operation 4.1 DC2 Generator Set/ Transfer Switch Controller4.2 Controls and Indicators 4.2.1 Controller Keypad 4.2.2 LED Indicators4.2.3 LCD Display 4.3 Controller Power4.4 Battery Charging 4.6 Event Log 4.5.3 Exerciser Reset4.5.2 Setting the Exerciser 4.5 Exercise4.8 OnCue Password 4.7 Maintenance TimerTP-6804 12/11 56 Section 4 DC2 Controller Operation5.1 Scheduled Maintenance Section 5 Scheduled Maintenance5.1.1 Service Schedule, 14RESA/RESAL Models 5.1.2 Service Schedule, 20RESA/RESAL Models 5.2.1 Low Oil Pressure Shutdown 5.2.4 Oil Change Procedure5.2 Lubrication System 5.2.3 Engine Oil RecommendationOil Capacity, L qt 5.2.5 Resetting the Maintenance Timer5.2.6 Oil Cooler 20RESA/RESAL Generator Set Model5.3 Spark Plugs 5.4 Air Cleaner Service5.4.1 Air Cleaner, 14RESA/RESAL Models tp6515 5.4.2 Air Cleaner, 20RESA/RESAL Models5.6 Exhaust System 5.5 Cooling SystemEZ-273000-J 5.7 Battery5.8.2 Fuel System 5.8 Storage Procedure5.8.5 Battery 5.8.1 Lubricating System6.1 Introduction Section 6 Troubleshooting6.2 Fault Messages 6.4 Controller Service AccessFigure 6-2 General Troubleshooting Chart 6.5 TroubleshootingDeutsches Institut fur Normung Appendix A AbbreviationsCalifornia Air Resources Board room temperature vulcanization sound power level, A weightedpositive temperature coefficient Occupational Safety and HealthPage E 2011 by Kohler Co. All rights reserved Kohler Power Systems Asia Pacific Headquarters 7 Jurong Pier RoadTP-6804 12/11 Singapore Phone 65 6264-6422, Fax