Manuals / Kohler / Lawn and Garden / Portable Generator

Kohler 14/20RESAL Resetting the Maintenance Timer, Oil Cooler 20RESA/RESAL, Generator Set Model

Models: 14/20RESAL 14/20RESA

1 72

Download 72 pages 24.65 Kb

Page 61

Generator Set Model

3.Fill with oil.

a.Fill the engine to the F mark on the dipstick. The engine oil capacity is shown in Figure 5-2. See Section 5.2.3, Engine Oil Recommendation, for oil selection.

Generator Set Model	Oil Capacity, L (qt.)

14RESA/RESAL	1.9	(2.0)

20RESA/RESAL	2.8	(3.0)

Figure 5-2 Engine Oil Capacity

b.Reinstall the dipstick and the oil fill cap.

c.Reconnect the generator set engine starting battery, negative (--) lead last.

d.Reconnect the utility power to the generator set.

e.Press the RUN button on the generator set controller. The generator set will start.

f.Run the generator set for a minute to allow the oil pressure to reach operating range.

g.Stop the generator set, wait 1 minute, and then recheck the oil level. Add oil to bring the level up to the F mark on the dipstick.

4.Check for leaks.

a.Check for oil leaks.

b.Fix leaks and recheck the oil level.

c.Reinstall the housing side panel.

5.Reset the maintenance timer on the controller.

5.2.5Resetting the Maintenance Timer

14/20RESA (RDC2):

1.In the Overview menu, step down to the Next Maintenance screen.

2.Press the Select button.

3.Press the Up arrow button so that Reset Maint Timer? Yes is displayed.

4.Press the Select button. The next maintenance interval and date will be displayed.

14/20RESAL (DC2):

1.Press and hold the OFF and AUTO buttons together until Maintenance Timer Reset is displayed.

2.Release the OFF and AUTO buttons.

5.2.6Oil Cooler 20RESA/RESAL

Inspect and clean the oil cooler at the intervals indicated in the service schedule. The oil cooler must be kept free of debris.

See Figure 5-3 for the oil cooler location. The oil cooler is located under the No. 2 cylinder shroud. Remove the top mounting screw and loosen the two side screws, then lift off the cylinder shroud.

Clean the outside of the oil cooler fins with a brush or with compressed air.

1. Oil cooler	1
1. Oil cooler	62 590 01

Figure 5-3 Oil Cooler Location

TP-6804 12/11

Section 5 Scheduled Maintenance 61

Image 61

Kohler 14/20RESAL manual Resetting the Maintenance Timer, Oil Cooler 20RESA/RESAL, Generator Set Model, Oil Capacity, L qt

Contents

Controllers ModelsTP-6804 12/11 OperationController Identification Product Identification InformationGenerator Set Identification Numbers Engine IdentificationUnloaded Cycle Exercise with Complete System Diagnostics Table of ContentsExercise TP-6804 12/11Table of Contents, continued Table of Contents, continued TP-6804 12/11 Battery Safety Precautions and InstructionsAccidental Starting Exhaust System Engine Backfire/Flash FireHazardous Noise Fuel SystemHazardous Voltage/ Moving Parts WARNINGCAUTIONHot Parts Heavy EquipmentList of Related Literature IntroductionEmission Information NameplateService Assistance TP-6804 12/11 14 Service Assistance1.5 Transfer Switch Section 1 Descriptions and Service Views1.1 Introduction 1.2 EngineRDC2 Controller Features DC2 Controller Features 1.7.1 Carburetor Heater 1.7 Accessories1.7.2 Fuel Regulator Heater 20RESA and RESAL only 1.7.3 OnCue Home Generator Management SystemFigure 1-2 Service View Model 20RESA shown 1.8 Service ViewsTP-6804 12/11 20 Section 1 Descriptions and Service ViewsSection 2 Generator Set Operation 2.1 Prestart Checklist2.2 Exercising the Generator Set 2.3 Generator Set Operation2.3.7 Automatic Operation with Model RDT or RSB Transfer Switches 2.3.6 Automatic Operation with Model RXT Transfer Switch2.4.2 Unloaded Cycle Exercise with Complete System Diagnostics 2.4.1 Setting the Exerciser2.4 Exercise 2.4.5 Power Failure During Exercise Cycle 2.5 Faults2.5.3 ATS Communication Errors 2.4.3 Unloaded Full-Speed Exercise2.5.4 Resetting the Controller after a Fault Shutdown Warning W or Figure 2-3 Controller Fault Messages TP-6804 12/11 28 Section 2 Generator Set Operation3.2 Controls and Indicators 3.1 RDC2 Generator Set/ Transfer Switch ControllerSection 3 RDC2 Controller Operation 3.2.1 Controller Keypad 3.2.2 LED Indicators3.2.3 LCD Display 3.4 Battery Charging 3.3 Controller Power3.5 Changing Settings Repeat steps 5 and 6, using the arrow and select When the correct date is shown, press the Select3.6.1 Setting the Exerciser at Controller Power--up 3.6 Setting the Exerciser3.6.2 Changing the Exercise Settings If the exerciser has not been set, No Exercise Sch will be displayed Figure 3-8 Procedure to Set the Exerciser on the RDC2 Controller3.8 Main Menu 3.7 RDC2 Controller Menus3.10 Engine Metering Menu 3.9 Overview MenuDANGER 3.11 Generator Metering Menu3.13 Genset Run Time Menu 3.12 Generator Set Information Menu3.14 Genset System Menu 3.15 ATS Status Menu 3.16 ATS Configuration Menu 3.18 Networking Information Menus 3.17 Date and Time Menu3.18.1 Networking Status Submenu 3.18.2 Networking Configuration Submenu OnCue Password 3.18.3 RBUS Information 3.18.4 Remote Devices Submenu 3.19 Programmable Interface Module PIM Status Menu 3.20 Load Control Module LCM Menus 3.21 Event Log 4.2 Controls and Indicators 4.1 DC2 Generator Set/ Transfer Switch ControllerSection 4 DC2 Controller Operation 4.2.1 Controller Keypad 4.2.2 LED Indicators4.4 Battery Charging 4.3 Controller Power4.2.3 LCD Display 4.5.2 Setting the Exerciser 4.5.3 Exerciser Reset4.5 Exercise 4.6 Event Log4.8 OnCue Password 4.7 Maintenance TimerTP-6804 12/11 56 Section 4 DC2 Controller Operation5.1 Scheduled Maintenance Section 5 Scheduled Maintenance5.1.1 Service Schedule, 14RESA/RESAL Models 5.1.2 Service Schedule, 20RESA/RESAL Models 5.2 Lubrication System 5.2.4 Oil Change Procedure5.2.3 Engine Oil Recommendation 5.2.1 Low Oil Pressure Shutdown5.2.6 Oil Cooler 20RESA/RESAL 5.2.5 Resetting the Maintenance TimerGenerator Set Model Oil Capacity, L qt5.4.1 Air Cleaner, 14RESA/RESAL Models 5.4 Air Cleaner Service5.3 Spark Plugs tp6515 5.4.2 Air Cleaner, 20RESA/RESAL Models5.6 Exhaust System 5.5 Cooling SystemEZ-273000-J 5.7 Battery5.8.5 Battery 5.8 Storage Procedure5.8.1 Lubricating System 5.8.2 Fuel System6.2 Fault Messages Section 6 Troubleshooting6.4 Controller Service Access 6.1 IntroductionFigure 6-2 General Troubleshooting Chart 6.5 TroubleshootingCalifornia Air Resources Board Appendix A AbbreviationsDeutsches Institut fur Normung positive temperature coefficient sound power level, A weightedOccupational Safety and Health room temperature vulcanizationPage TP-6804 12/11 Kohler Power Systems Asia Pacific Headquarters 7 Jurong Pier RoadSingapore Phone 65 6264-6422, Fax E 2011 by Kohler Co. All rights reserved