LevelOne 11g PoE Wireless Access Point, WAP-0005 instruction

Installation

3.Connect the supplied power adapter to the Wireless Access Point and a convenient power outlet, and power up.

NOTE: If you wish to use PoE (Power over Ethernet), refer to the following section.

4.Check the LEDs:

•The Status LED should flash, then turn OFF.

•The Power, Wireless LAN, and LAN LEDs should be ON.

For more information, refer to Front Panel LEDs in Chapter 1.

Using PoE (Power over Ethernet)

WAP-0005 supports PoE (Power over Ethernet). To use PoE:

1.Do not connect the supplied power adapter to the Wireless Access Point.

2.Connect one end of a standard (category 5) LAN cable to the Ethernet port on the Wireless Access Point.

3.Connect the other end of the LAN cable to the powered Ethernet port on a suitable PoE Injector.

4.Connect the unpowered Ethernet port on the PoE adapter to your Hub or switch.

5.Connect the power supply to the PoE injector and power up.

6.Check the LEDs on the Wireless Access Point to see it is drawing power via the Ethernet connection.

PoE Injector

Figure 5: Using PoE (Power over Ethernet)

7

Image 11

LevelOne 11g PoE Wireless Access Point, WAP-0005 manual Using PoE Power over Ethernet

Contents

Users Guide Page Table of Contents Overview Command Reference Wireless Access PointOverview General Problems Overview Wireless LAN Terminology Introduction Features of your Wireless Access Point Advanced Features Security Features Introduction Physical Details Package Contents Rear Panel Requirements InstallationProcedure Requirements Using PoE Power over Ethernet Using PoE Power over EthernetPage Overview Access Point SetupSetup using the Windows Utility Installation Buttons Wireless Access Points Pass-phrase just works for Hex and not for Setup Procedure Password Dialog Setup using a Web Browser If you cant connect Buttons Access ControlData Access Control Screen Data Trusted Wireless Stations Trusted Wireless Stations Add Security ProfilesSelect None Edit Isolation Data Security Profiles ScreenProfile Primary Profile Security System Wireless BandSecurity Profile Screen Profile Data Setup Using MAC authentication Security Settings NoneRadius MAC Authentication Setup Data Radius-based MAC Authentication Screen Radius-based MAC authentication Screen UAM authentication External UAM authentication Internal Data UAM Screen UAM Screen Security Settings WEP Data WEP Screen WPA Encryption Security Settings WPA-PSKData WPA-PSK Screen Network Key When any membership Pairwise Key UpdateGroup Key Update Update Group key WPA-802.1x Wireless Security Security Settings WPA-802.1x WPA-802.1x Data WPA-802.1x Screen Every Update Report 802.1x Wireless Security Security Settings 802.1x Data 802.1x Screen UAM IP Address System ScreenData System Screen Identification Wins Server Name/IP Address Wireless Mode Wireless ScreensBasic Settings Screen Data Basic Settings Screen MAC Address field AP ModeBridge Mode Broadcast Ssid Parameters Options Advanced SettingsData Advanced Settings Screen Basic Rate 802.11b Security PC and Server ConfigurationUsing WEP Using WPA-PSK 802.1x Using WPA-802.1xWireless Station Configuration Radius Server Configuration Services Installation 802.1x Server Setup Windows 2000 ServerWindows 2000 Domain Controller Setup Components Screen CA Screen Dhcp server configuration IP Address Screen Certificate Authority Screen Certificate Authority Setup Active Directory Screen Group Policy Screen Service Screen Internet Authentication Service Radius Setup Authentication Screen Dial-in Screen Remote Access Login for Users Client Certificate Setup 802.1x Client Setup on Windows XP Wireless CA Screen Identifying Information Screen Encryption Settings 802.1x Authentication Setup Enabling Encryption Wireless Networks Screen Properties Screen Using 802.1x Mode without WPA Status Screen Operation and StatusOperation Security Profiles Access PointWireless Data Status Screen System Up Time 4GHz WirelessStatistics Screen Data Statistics Screen Control Multicast PacketsManagement Clients Profile StatusBand Data Activity LogData Activity Log Refresh Button Station ListData Station List Screen Station List Admin Login Screen Access Point Management Admin Connections Data Admin Login ScreenLogin Perform Auto Auto Config/UpdateData Auto Config/Update Screen Configuration on this AP Auto Update Restore Config FileData Config File Screen Backup Revert to factory Defaults Data Log Settings Screen Log Settings Syslog Data Rogue AP Screen Enable DetectionRogue APs Traps Data Snmp ScreenGeneral Managers To perform the Firmware Upgrade Upgrade Firmware Wireless Specifications SpecificationsWireless Access Point Hardware Specifications Feature Details Software Specifications Message Log FCC Radiation Exposure Statement FCC Statement To Find the Access Points IP Address TroubleshootingGeneral Problems Wireless Access Point User Guide Normally, no changes need to be made Checking TCP/IP Settings Windows 9x/MEWindows TCP/IP Using Specify an IP Address Using Dhcp Windows NT4.0 TCP/IP Checking TCP/IP Settings Windows NT4.0 Obtain an IP address from a Dhcp Server Network Configuration Win Checking TCP/IP Settings Windows Using a fixed IP Address Use the following IP Address Network Configuration Windows XP Checking TCP/IP Settings Windows XP Using Dhcp Infrastructure Mode About Wireless LANsWireless LAN Terminology Ad-hoc Mode WPA-802.1x Channels 802.1x Using the CLI Serial Port Command Line InterfaceUsing the CLI Telnet CLI Port Settings Command Reference Wireless Access Point User Guide Display 11g Beacon Rate Wireless Access Point User Guide Mem -- system memory statistics Set 11g Beacon Rate Appendix C Windows TCP/IP Wireless Access Point User Guide