11g USB Adapter w/LCD WiFi Detector
WNC-0304USB
User Manual
LevelOne
HOW TO USE THE WI-FI DETECTOR
CONTENTS
HOW TO CHARGE THE BATTERY OF WI-FI DETECTOR
HOW TO INSTALL THE DRIVER AND UTILITY
1.1 Features
1 Introduction
1.2 Specifications
WNC-0304USB USB Cable CD Manual/Driver/Utility
1.3 Package Contents
Quick Installation Guide
2 How to charge the battery of Wi-Fi Detector
3 How to use the Wi-Fi Detector
The Icons on the LCD display are displayed as follows
Seek/Lock
4 How to install the driver and utility
4.1 Install the Configuration Utility
Please click “Next” to continue the installation
Click “Finish” to complete the installation
4.2 Install the USB adapter
Click “Finish” to complete the installation
4.3 Using the Configuration Utility
First Way
A. Double-click the icon B. Click “Advance”
Second Way
C. Uncheck “Use Windows to configure my wireless network settings”
5 How to configure the utility
5.1 Wireless Connection Status
More Setting
connecting to. The information includes Channel, Type, SSID, TX
Rate and Encrypt settings. Note Please refer to Section 5.2 for
For setting more functions including disable/enable WEP and
5.2 General Connection Setting
to one of the available wireless stations without checking the
When the adapter works in 11b mode, the maximum data rate is
If “Any“ check box is enabled, the adapter will survey and connect
consistency of channel and SSID with the wireless station
Open System - No authentication is needed among the wireless
Authentication Mode
This setting has to be consistent with the wireless networks that
Shared Key - Only wireless stations using a shared key WEP
5.3.1 WEP Setting
5.3 WEP and WPA Encryption
“01234567890123456789abcdef“ or “administrator“
Default Key ID
The keys are used to encrypt data transmitted in the wireless
Clcik “Change“ will enable you to setup the WEP key. In the
Page
5.3.2 WPA/WPA2 Setting
Page
TTLS require a set of user name and password in addition. To get
It is the setting for WPA mode
This adapter supports three kinds of protocol for authentication
the certificate and the personal user name and password, please
5.4 Advanced Settings
Continuous Access Mode CAM - The adapter will always set
“Maximum Power-Saving“ mode
saving mode when it is idle, but some components of the adapter
is still alive. In this mode, the power consumption is larger than
PSP XLink Mode
5.5 Software AP Mode
5.5.2 AP Connection Status
5.5.2 AP General Connection Setting
wireless adapters set the same SSID can connect to the AP. It
If “Hide SSID“ check box is enabled, the AP will not appear in the
site survey list of any wireless adapters. It means Only the
Clcik “Change“ will enable you to setup the parameters of
should use the shorter preamble type
Wireless adapters connect to the AP can access to the wired
adapter in the list be the bridge between the wireless and wired
MAC Address Filter
5.5.3 MAC Address Filter
1 Open Control Panel --Æ Internet Connection
6 X-Link Installation
Right Click “Wireless Network Connection” and select “Properties”
Page
Then select “Advanced”
6 Setting completed, please turn your PSP into online status
8 Start the X-Link software after the installation
Clicks “OK” to start online gaming
2. What is the IEEE 802.11b standard?
7 Troubleshooting
1. What is the IEEE 802.11g standard?
3. What does IEEE 802.11 feature support?
7. What is WEP?
5. What is Infrastructure?
6. What is BSS ID?
8. What is TKIP?
14. What is the maximum AP that can be detected?
12. What is DSSS?What is FHSS?And what are their differences?
13. What is Spread Spectrum?
15. What is the maximum detection distance?