LevelOne
WNC-0304USB
User Manual
11g USB Adapter w/LCD WiFi Detector
HOW TO INSTALL THE DRIVER AND UTILITY
CONTENTS
HOW TO CHARGE THE BATTERY OF WI-FI DETECTOR
HOW TO USE THE WI-FI DETECTOR
1 Introduction
1.1 Features
1.2 Specifications
1.3 Package Contents
Quick Installation Guide
WNC-0304USB USB Cable CD Manual/Driver/Utility
2 How to charge the battery of Wi-Fi Detector
3 How to use the Wi-Fi Detector
The Icons on the LCD display are displayed as follows
Seek/Lock
4.1 Install the Configuration Utility
4 How to install the driver and utility
Please click “Next” to continue the installation
Click “Finish” to complete the installation
4.2 Install the USB adapter
Click “Finish” to complete the installation
First Way
4.3 Using the Configuration Utility
Second Way
C. Uncheck “Use Windows to configure my wireless network settings”
A. Double-click the icon B. Click “Advance”
5 How to configure the utility
5.1 Wireless Connection Status
For setting more functions including disable/enable WEP and
connecting to. The information includes Channel, Type, SSID, TX
Rate and Encrypt settings. Note Please refer to Section 5.2 for
More Setting
5.2 General Connection Setting
consistency of channel and SSID with the wireless station
When the adapter works in 11b mode, the maximum data rate is
If “Any“ check box is enabled, the adapter will survey and connect
to one of the available wireless stations without checking the
Shared Key - Only wireless stations using a shared key WEP
Authentication Mode
This setting has to be consistent with the wireless networks that
Open System - No authentication is needed among the wireless
5.3 WEP and WPA Encryption
5.3.1 WEP Setting
Clcik “Change“ will enable you to setup the WEP key. In the
Default Key ID
The keys are used to encrypt data transmitted in the wireless
“01234567890123456789abcdef“ or “administrator“
Page
5.3.2 WPA/WPA2 Setting
Page
the certificate and the personal user name and password, please
It is the setting for WPA mode
This adapter supports three kinds of protocol for authentication
TTLS require a set of user name and password in addition. To get
Continuous Access Mode CAM - The adapter will always set
5.4 Advanced Settings
PSP XLink Mode
saving mode when it is idle, but some components of the adapter
is still alive. In this mode, the power consumption is larger than
“Maximum Power-Saving“ mode
5.5.2 AP Connection Status
5.5 Software AP Mode
5.5.2 AP General Connection Setting
Clcik “Change“ will enable you to setup the parameters of
If “Hide SSID“ check box is enabled, the AP will not appear in the
site survey list of any wireless adapters. It means Only the
wireless adapters set the same SSID can connect to the AP. It
MAC Address Filter
Wireless adapters connect to the AP can access to the wired
adapter in the list be the bridge between the wireless and wired
should use the shorter preamble type
5.5.3 MAC Address Filter
6 X-Link Installation
Right Click “Wireless Network Connection” and select “Properties”
1 Open Control Panel --Æ Internet Connection
Page
Then select “Advanced”
8 Start the X-Link software after the installation
6 Setting completed, please turn your PSP into online status
Clicks “OK” to start online gaming
3. What does IEEE 802.11 feature support?
7 Troubleshooting
1. What is the IEEE 802.11g standard?
2. What is the IEEE 802.11b standard?
8. What is TKIP?
5. What is Infrastructure?
6. What is BSS ID?
7. What is WEP?
15. What is the maximum detection distance?
12. What is DSSS?What is FHSS?And what are their differences?
13. What is Spread Spectrum?
14. What is the maximum AP that can be detected?