WNC-0304USB
User Manual
11g USB Adapter w/LCD WiFi Detector
LevelOne
CONTENTS
HOW TO CHARGE THE BATTERY OF WI-FI DETECTOR
HOW TO USE THE WI-FI DETECTOR
HOW TO INSTALL THE DRIVER AND UTILITY
1.1 Features
1 Introduction
1.2 Specifications
1.3 Package Contents
Quick Installation Guide
WNC-0304USB USB Cable CD Manual/Driver/Utility
2 How to charge the battery of Wi-Fi Detector
3 How to use the Wi-Fi Detector
The Icons on the LCD display are displayed as follows
Seek/Lock
4 How to install the driver and utility
4.1 Install the Configuration Utility
Please click “Next” to continue the installation
Click “Finish” to complete the installation
4.2 Install the USB adapter
Click “Finish” to complete the installation
4.3 Using the Configuration Utility
First Way
Second Way
C. Uncheck “Use Windows to configure my wireless network settings”
A. Double-click the icon B. Click “Advance”
5 How to configure the utility
5.1 Wireless Connection Status
connecting to. The information includes Channel, Type, SSID, TX
Rate and Encrypt settings. Note Please refer to Section 5.2 for
More Setting
For setting more functions including disable/enable WEP and
5.2 General Connection Setting
When the adapter works in 11b mode, the maximum data rate is
If “Any“ check box is enabled, the adapter will survey and connect
to one of the available wireless stations without checking the
consistency of channel and SSID with the wireless station
Authentication Mode
This setting has to be consistent with the wireless networks that
Open System - No authentication is needed among the wireless
Shared Key - Only wireless stations using a shared key WEP
5.3.1 WEP Setting
5.3 WEP and WPA Encryption
Default Key ID
The keys are used to encrypt data transmitted in the wireless
“01234567890123456789abcdef“ or “administrator“
Clcik “Change“ will enable you to setup the WEP key. In the
Page
5.3.2 WPA/WPA2 Setting
Page
It is the setting for WPA mode
This adapter supports three kinds of protocol for authentication
TTLS require a set of user name and password in addition. To get
the certificate and the personal user name and password, please
5.4 Advanced Settings
Continuous Access Mode CAM - The adapter will always set
saving mode when it is idle, but some components of the adapter
is still alive. In this mode, the power consumption is larger than
“Maximum Power-Saving“ mode
PSP XLink Mode
5.5 Software AP Mode
5.5.2 AP Connection Status
5.5.2 AP General Connection Setting
If “Hide SSID“ check box is enabled, the AP will not appear in the
site survey list of any wireless adapters. It means Only the
wireless adapters set the same SSID can connect to the AP. It
Clcik “Change“ will enable you to setup the parameters of
Wireless adapters connect to the AP can access to the wired
adapter in the list be the bridge between the wireless and wired
should use the shorter preamble type
MAC Address Filter
5.5.3 MAC Address Filter
6 X-Link Installation
Right Click “Wireless Network Connection” and select “Properties”
1 Open Control Panel --Æ Internet Connection
Page
Then select “Advanced”
6 Setting completed, please turn your PSP into online status
8 Start the X-Link software after the installation
Clicks “OK” to start online gaming
7 Troubleshooting
1. What is the IEEE 802.11g standard?
2. What is the IEEE 802.11b standard?
3. What does IEEE 802.11 feature support?
5. What is Infrastructure?
6. What is BSS ID?
7. What is WEP?
8. What is TKIP?
12. What is DSSS?What is FHSS?And what are their differences?
13. What is Spread Spectrum?
14. What is the maximum AP that can be detected?
15. What is the maximum detection distance?