Installer Menu (Cont.)
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/ Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.
029 - OLD OCV (On Command Video™)
Set to 1 for operation with systems from On Command Corporation.
030 - ACK MASK
MPI Communication Parameter. Leave at default setting unless changed by
031 - POLL RATE
MPI Communication Parameter. Selects Poll Rate for MPI. Leave at default setting unless changed by
032 - TIMING PULSE
MPI Communication Parameter. Leave at default setting unless changed by
034 - CAMPORT EN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.
Note: (26/32LG3DCH only)
035 - COMPPORT EN. (Computer Port Enable) Enable/disable TV display panel HDMI 1 input jack. Set to 0 to disable HDMI1. Set to 1 to enable HDMI1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.
Note: (26/32LG3DCH only)
040 - AUTO CAMPORT
Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection.
Note: If set to 1, STRT AUX SRCE cannot be set at 2.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting AUX source. When turned On, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = Video 1 | 4 | = RGB | 255 = Last Aux |
2 = Video 2 | 6 | = Component |
|
3 = HDMI 1 |
|
|
|
If item 040 AUTO CAMPORT is set to 1:
1 = Video 1 | 4 | = RGB |
3 = HDMI 1 | 6 | = Component |
Note: Above is applicable only if all Aux sources are enabled.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change. Controls MPI status channel response for Aux inputs.
053 - DIS.
Set to 1 to disable the
069 - EN.
070 - FOR.
Set according to Color Chart: |
|
| |||
0 | = Black | 3 | = Cyan | 6 | = Yellow |
1 | = Blue | 4 | = Red | 7 | = White |
2 | = Green | 5 | = Violet |
|
|
Notes: Applies only to “Channel Not Available” message if item 073 is set to 1, enabled. If foreground color and background color are the same, the menu background will be transparent.
071 - BCK.
0 | = Black | 3 | = Cyan | 6 | = Yellow |
1 | = Blue | 4 | = Red | 7 | = White |
2 | = Green | 5 | = Violet |
|
|
Notes: Applies only to “Channel Not Available” message if item 073 is set to 1, enabled. If foreground color and background color are the same, the menu background will be transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL- ABLE” message is displayed when directly accessing a channel not in the channel scan list available in memory.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, TV automati- cally tunes to the specified Start Channel.
077 - QUICK SHUTOFF
Allows TV power Off event to be controlled by the remote control, TV front panel and Pillow Speaker Channel Up/Down buttons. End user would push and hold channel button down for time required to have TV turn Off. Setting 0 = disabled. Value Range 0 - 17, each number represents 1/2 second. For example, if set to 4, TV would turn Off if end user held any channel button down for two seconds.
22 |