| OPERATION | |||||
|
|
|
|
|
|
|
|
|
| USER DEFINED PARAMETERS |
|
|
|
|
|
|
|
|
| |
Parameter | Definition |
|
|
| ||
|
|
| Exit Setup Menu |
|
|
|
| P.0 | This option is used to exit the setup menu. When P.0 is displayed, press the Left Button to exit | ||||
|
|
| the setup menu |
|
|
|
|
|
|
|
|
| |
| P.1 | Wire Feed Speed Units |
|
|
| |
|
|
| This option selects which units to use for displaying wire feed speed. English = inches/minute | |||
|
|
| wire feed speed units (default). Metric = meters/minute wire feed speed units. |
|
|
|
|
|
|
|
|
| |
| P.2 | Arc Display Mode |
|
|
| |
|
|
| This option selects what value will be shown on the upper left display while welding. Amps = | |||
|
|
| The left display shows Amperage while welding (default). WFS = The left display shows Wire | |||
|
|
| Feed Speed while welding. |
|
|
|
|
|
|
|
|
| |
| P.3 | Display Energy |
|
|
| |
|
|
| This option selects whether or not energy is shown on the lower display while welding. The total | |||
|
|
| energy from the previous weld will persist on the lower display until another weld is started, or a | |||
|
|
| user interface control is changed. This option will only show up in the list if the power source is | |||
|
|
| capable of calculating energy (a power source firmware update may be necessary). |
|
|
|
|
|
| No = Energy will not be displayed (default). Yes = Energy is displayed. |
|
|
|
|
|
|
|
|
| |
| P.12 | Travel Carriage Start/Stop - Travel Starts |
|
|
| |
|
|
| This option allows the adjustment of the start and end travel options for a travel carriage. Press | |||
|
|
| the Right Button to enter the option and rotate the Control Knob to select either starting or end- | |||
|
|
| ing options. Press the Right Button to enter the selected option. Rotate the Control Knob to | |||
|
|
| select the desired function. After selecting the function, press the Left Button to save the func- | |||
|
|
| tion and back out to select another option. Rotate the Control Knob to make another selection, | |||
|
|
| or press the Left Button to exit this option. |
|
|
|
|
|
|
|
|
| |
| P.12 | Travel Carriage Start/Stop - Travel Ends |
|
|
| |
|
|
| This option allows the adjustment of the start and end travel options for a travel carriage. Press | |||
|
|
| the Right Button to enter the option and rotate the Control Knob to select either starting or end- | |||
|
|
| ing options. Press the Right Button to enter the selected option. Rotate the Control Knob to | |||
|
|
| select the desired function. After selecting the function, press the Left Button to save the func- | |||
|
|
| tion and back out to select another option. Rotate the Control Knob to make another selection, | |||
|
|
| or press the Left Button to exit this option. |
|
|
|
|
|
|
|
|
| |
| P.13 | Arc Force Adjustment Options |
|
|
| |
|
|
| This option allows the adjustment of Arc Force values for Start, Weld and Crater. Press the | |||
|
|
| right Mode Select Button to enter the option and rotate the Set knob to select the desired weld | |||
|
|
| state to adjust. Press the right button again to adjust the value on the upper left knob. Press | |||
|
|
| the left button to save the value and back out to select another weld state. Rotate the Set knob | |||
|
|
| to make another selection, or press the left button to exit this option. P.13 will not appear if the | |||
|
|
| presently selected weld mode does not support Arc Force. |
|
|
|
|
|
|
|
|
| |
| P.14 | Reset Consumable Weight |
|
|
| |
|
|
| Use this option to reset the initial weight of the consumable package. Press the Right Button to | |||
|
|
| reset the consumable weight. This option will only appear with systems using Production | |||
|
|
| Monitoring. |
|
|
|
|
|
|
|
|
|
|
MAXsa™ 10 CONTROLLER
